Shave the bottom of the pocket door so it clears the tile. You have about an inch and a half of plug inside the hollow core door to trim. Don’t shave more than 3/4″ off the bottom. If you can, trim equal amounts off the top and bottom.
How do you shorten the bottom of a door?
Quote from the video:
Quote from Youtube video: Just deep enough to cut through the door carefully use your circular saw to make the cut holding onto your waste piece as you complete finish by touching up any rough edges with a sanding block.
Can you trim the bottom of a door with a multi tool?
1) Trim the bottoms of door jambs and casing in place
When you need to trim the bottom of a door jamb or casing to let in new flooring or a saddle for transition between rooms, there’s no simpler way to do it than with a multitool fitted with a plunge-cutting blade.
How do you cut a pocket door in place?
Quote from the video:
Quote from Youtube video: So you know you would just line it up with with the first piece you put on and then that hides not being able to look back inside the door. So keep that in mind.
How do you trim the bottom of a door without taking it off?
Quote from the video:
Quote from Youtube video: We need to use a clamp which is a quick release clamp. And we need to use a square. And they work together because there's a slot in. It. If we use the two together which slide this one in first.
What tool do I use to cut the bottom of a door frame?
Quote from the video:
Quote from Youtube video: So what do you need to cut the bottom of door jams off. So that your flooring will actually slide up underneath it. Well you need some kind of a flush cut saw this one here is from Stanley.
How do you trim the bottom of a door trim?
Quote from the video:
Quote from Youtube video: It's going to be the thickness of the actual pad plus the floor up against the actual casing or door molding so what you want to do is I have a scrap here. And I always mark my cut-offs with an X.
Can you trim the bottom of a door?
Quote from the video:
Quote from Youtube video: This is to help me get a cleaner cut when i run the saw along the line i'm about to draw. I'm going to measure off a half inch on both ends of the door. Then take a level and mark.
Can you saw the bottom of a door?
The Best Way to Cut Off a Door Bottom
If you’ve just installed carpeting, your doors will probably rub and bind, which means that you have to trim off the bottoms. Trimming a wood door with a circular saw without splintering the wood or damaging the finish is a challenge.
How do you cut the bottom of a door with a planer?
Quote from the video:
Quote from Youtube video: Now what I like to do is plain the door from the outside edges to the center. So I begin on one side of the door plane it from the outside edge to the center. Then I go from I stop to in the center.
How do you shave down a door?
- Step 1: Find the Rub. Close the door just enough so that it sticks or rubs — don’t shut it all the way. …
- Step 2: Remove the Door From the Jamb. …
- Step 3: Mark it For Shaving. …
- Step 4: Set and Position. …
- Step 5: Shave the Door. …
- Step 6: Check and Repeat. …
- Step 7: Rehang and Check.
How much should I cut off the bottom of a door for carpet?
One of the best ways to make sure you are cutting off the bottom and not the top of a door is to measure to the door hardware location, which should be about 36 inches from the bottom. Lay a pencil on the carpet to mark the cut-off elevation on the door face.
Can you use an electric planer to trim a door?
Doors that rub the floor or jamb are flat out annoying. This problem is typically fixed by tightening or shimming hinges. But sometimes the door just needs to be shaved down a tiny bit and this can be accomplished by using a power planer.
How do you trim the edge of a door that is too wide?
If a door is just a little bit too wide, remove the hinges and trim the hinge-side stile only. But if you have to trim off both sides, you’ll have to reposition the latching hardware. Remember to leave a 1/8-inch gap at the top and each side of the door, and a 1/4-inch gap at the bottom.
What is a door planer?
Quote from the video:
Quote from Youtube video: The power planer uses a rotating cutting head to do the work and a hand planer uses a knife blade or cutting edge that slides down below and the axial leverage or hand movement of the planer.
