What is a slip-on tub spout?

A slip-fit spout has an internal assembly that slips over a copper pipe. The spout has an opening on the bottom side where a setscrew is tightened to hold the spout onto the copper pipe. A slip-fit spout does not contain threads.

What is the difference between a diverter and non diverter tub spout?





Diverter or Non-Diverter



A diverter tub spout will have a lift rod that you pull up and push down on to divert the water between the showerhead and tub spout. A non-diverter tub spout will not have a lift rod (generally, used in a tub only or a three handle tub and shower configuration).

What kind of tub spout do I have?

How To Determine What Type of Tub Spout You Already Have

  • Grab a flashlight and look beneath the tub spout while it still attached to the wall. If you can see a tiny screw on the underside of the spout, you have a slip-on tub spout with a set screw.
  • If there is no set screw, you have a threaded tub spout.


How do you fix a diverter tub spout?

Quote from the video:
Quote from Youtube video: And fortunately i bought a repair piece for it. So this is turned in to a replacement rather than a repair. Although you could certainly file that down and repair. It.

How does a tub spout diverter work?





When the diverter valve is open, water flows directly through the faucet and into the tub. However, when you want to take a shower, you lift the knob or lever to close the diverter valve. This creates pressure, forcing the water flow upward and out of the showerhead.

How do you remove a slip on tub spout?

Replacing a slip-on spout is easy: Just loosen the setscrew (usually with a hex wrench) and pull the spout off the copper pipe that protrudes from the wall. Twist the spout as you pull and be gentle so you don’t loosen any pipe connections inside the wall. Then slide on the new spout and tighten the setscrew.

How does a pull down diverter tub spout work?

The diverter pulls down easily, and seals perfectly (no leaking water out of the spout while the shower is on). When the water is turned off, the decreased pressure lets the diverter automatically pop back up, so the next time you turn the water on you don’t get an unintentional shower.

What are the different types of tub diverters?

There are three different types of shower diverters:

  • Three-valve diverter – These are usually found when there are separate knobs for hot and cold water. …
  • Two-valve diverter – This type of diverter is usually found with a single-handle faucet. …
  • Single-valve or T diverter – This is the most common type of diverter.



What is the difference between a transfer valve and a diverter valve?

The main difference between a diverter and a transfer valve is how they direct the water supply. Diverters switch the flow of water between a tub and shower—either the showerhead or the tub faucet gets the water flow. Transfer valve sends water to multiple outlets at the same time.

How do you install a spout diverter kit?

Quote from the video:
Quote from Youtube video: And this is what your rod grabs a hold of inside your spout. And this rubber little grommet gasket has to be in there. And in the event that yours pops out i want to show you how to put this back in.

How do you fix a diverter valve?



How to Repair a Shower Diverter

  1. Turn off the water supply to your shower.
  2. Seal off your drain with tape so that small screws or other important parts are not lost down the drainpipe.
  3. Tighten the screws behind the faceplate of the diverter valve. …
  4. Disassemble the shower diverter. …
  5. Replace the diverter.

How do you replace a tub diverter valve?

Quote from the video:
Quote from Youtube video: If you over tighten it you could cause internal damage to the valve. And that would not be good get a pretty snug hand tight and then from there we'll grab our wrench. And from here grab the wrench.

How do you adjust a shower diverter?

Quote from the video:
Quote from Youtube video: Pull it off thing off just pulls right off. Take it in you can adjust the temperature. Just wear that link left or right to make it hotter or colder in most cases you won't make it hotter.

How does a 3 way diverter valve work?

The three-way diverter allows you to alternate between any of your selected shower outputs by directing the water from the shower head to each additional accessory, one at a time. The diverter will not adjust the water temperature or turn the water off or on. All rough-in work should be completed by a professional.

How does a 3 function shower diverter work?



A three-valve shower has three different handles that you turn to open or close the valves. One handle opens the hot water valve, one opens the cold water valve, and the third (generally in the middle of the temperature valves) diverts the water into the spigot or up to the shower head.

How do you install a 3 way shower diverter?

Quote from the video:
Quote from Youtube video: To the drain. The line right on the center of my drain. And we're square. That being the center of it i know this pipe is directly in the center.

How does a 6 way diverter valve work?

The 6 setting allow you to control each spray individually, or any combination of 2 spray groups at the same time. The body sprays will be plumbed on a pressure loop and function together as a unit. The tub spout does not connect to the diverter in any way.

What does a shower diverter look like?

Quote from the video:
Quote from Youtube video: Comes in from the left cold. Water from the right the two are mixed in the valve. And will either go up to the showerhead or down to a tub spout a diverter directs which way the water goes.

What does a diverter valve spacer do?



The diverter spacer is supposed to allow the stock diverter to allow more air to divert than stock. The diverter valve and blow off valve do the same thing for the most part, but you want to stick with the diverter valve.