Why does my pilot light keep going out with a new thermocouple?

If your water heater pilot won’t stay lit even after replacing the thermocouple, you most likely have a faulty gas control valve. It is a sign that the valve is failing to open and allow gas to flow to the pilot. You could also be dealing with a tripped or faulty thermal switch.

What would cause a pilot light to keep going out?





A faulty, misaligned, dirty, or damaged thermocouple is often the culprit behind your pilot light going out. The thermocouple is an automatic safety shutoff device that prevents the gas valve from opening if the pilot light is out.

Why does my pilot light keep going out on my propane heater?

If the thermocouple is too far from the flame, this can cause the pilot to go out and shut down the propane heater; you can fix this easily by moving the thermocouple closer to the flame. The thermocouple could also be worn out, in which case it needs to be replaced.

Why does my hot water pilot keep going out?

The most common reason that your pilot light on your water heater keeps going out is a damaged, bent or dirty thermocouple.

How do I stop the wind from blowing out my pilot light?

A pilot light shield will cover the pilot light to help prevent it from going out. You can buy one at the hardware store and install it yourself to see if that resolves the problem. Will work best if the problem keeps happening due to a draft in the room. Many gas water heaters connect to the chimney for ventilation.

Will the gas company light My pilot?





PG&E is encouraging customers to call 1-800-PGE-5000 now to schedule an appointment to turn on furnace pilot lights for winter and check natural gas appliances for safety and efficiency. PG&E gas service professionals relight appliance pilots at no extra cost.

Does gas still flow when pilot light goes out?

This electric current energises an electromagnet that in turn keeps a gas valve open allowing gas to flow to the main burner. If the pilot light goes out for any reason, the current stops, the valve closes, thus preventing any gas from leaking.

Does the pilot light go out when the gas is turned off?

Your pilot light relies on your natural gas to stay aflame, so if your gas is shut off, your pilot light will go out. Simply turn your gas back on and either relight your pilot light yourself or call a professional.

Does gas leak if pilot light goes out?

Because it’s a byproduct of combustion, your gas appliances won’t emit any carbon monoxide if a pilot light goes out. They could, however, leak gas, so it’s still important to exercise caution when the pilot light goes out.

Should the pilot light always be on in a gas heater?



Should The Pilot Light Always Be On In A Gas Furnace? Yes, if the furnace is in operation, the pilot light will need to be on for it to be functional. However, some homeowners turn off their furnace’s pilot light in the warmer seasons when the gas furnaces aren’t in use.

How do you light a hot water heater without an igniter?

Lighting with No Igniter

  1. Take a long lighter to reach the pilot. …
  2. Remove the plate attached below the dial box. …
  3. Switch Pilot to OFF.
  4. Wait for a while, – 5-10 minutes until there won’t be any gas.
  5. Change the temperature to LOW, and switch to Pilot.
  6. Push ON/OFF dial down, and simultaneously use the lighter.

Can you manually light a water heater with electronic pilot?

They use electronic ignition to ignite the gas. Do not attempt to manually light an electronic ignition system. If the pilot light is not lit: Attempt to re-light the pilot light, following the instructions posted on your water heater.

Can you manually light a hot water heater?



Lighting the Pilot Light on a Manual Hot Water Heater

Turn the pilot dial to the off position and wait 5-10 minutes for any gas to dissipate. Then, turn the pilot dial until it says the word pilot. After that, set your temperate knob to low. Now, hold the pilot dial down while you light the burner.

Can I relight the pilot light by myself?

If your pilot light goes out, your furnace will not be able to produce heat because its burners will not ignite. Often, homeowners can relight the pilot themselves.

How do you reignite a pilot light?

Turn the knob to “Pilot” and hold down the “Reset” button.



Using a long lighter, bring the flame close to the pilot opening. This should ignite the pilot light. Once the pilot is lit, you can release the reset button. The pilot should stay lit at this point.

How much does it cost to have a pilot light lit?

A pilot light is a small flame that is kept lit to provide a catalyst for the main burner to be turned on when needed. The average fuel consumption of your standing Pilot light is: Natural gas is $0.60 a day = $219 a year. Liquid Propane is $1.80 a day = $657 a year.

How do you reset an automatic pilot light?

These steps outline the standard procedure for relighting a standing pilot light on a gas furnace.

  1. Step 1: Remove the Access Cover. …
  2. Step 2: Identify the Pilot Parts. …
  3. Step 3: Turn Off the Gas and Wait. …
  4. Step 4: Get Ready To Light. …
  5. Step 5: Light the Pilot. …
  6. Step 6: Turn On the Gas.

Can you manually light a gas furnace with electronic ignition?



If your furnace is equipped with an electronic igniter, you cannot light the furnace manually. However, you may be able to get the furnace working by turning off the igniter and resetting it. Find the paperwork for your particular furnace to locate the reset button or switch.

What is an intermittent pilot?

Intermittent Pilot Ignition is an electronic system, which uses an electrode to ignite the pilot gas. In turn, the pilot flame lights the main burner gas. The term Intermittent is used because the pilot burner flame is only present when the main burner is operating. When the main burner is off the pilot is also off.