I would not. It was probably left long like that because the attachments (bolts, screws, nails) are right where the slant is, so if you cut off the tail piece, those fasteners are now too close to the end of the wood and will break out.

How do you cut a newel post?

Quote from the video:
Quote from Youtube video: Cut. These pieces need to be mitered. Together to form part of the cap of the noodle post. We can put those joints together using pocket screws. And it's really important that that be a durable joint.

Are newel posts structural?





A newel post is the structural upright post that fits at the beginning and the end of a staircase and supports the handrail of a stair banister. The most important job of a newel post is to provide structural support, but that does not mean that they can’t be used to enhance the look and feel of your stairs.

Is a newel post load bearing?

As mentioned, newel posts are found at the foot of the stairs and at every turn (at a landing or any 90-degree turn), whether the staircase is inside or outside. Just as a house has load-bearing walls for support, a staircase has newel posts to bear the weight of the staircase.

Can you cut a newel post in half?

To cut a turned one in half, all you need to do is temporarily pin a straight piece of timber to the side of it flush with the top. Then use that as the guide for your saws fence.

How much does it cost to replace a newel post?

Cost to Install Newel Post



The average price to install a newel post is $365, including labor costs and mid-range materials. Single posts cost $35 to $550.

What is the difference between a baluster and a newel?





is that baluster is (architecture) a short column used in a group to support a rail, as commonly found on the side of a stairway; a banister while newel is (architecture) a sturdy pillar at the top or bottom of a flight of stairs, supporting the handrail.

What is half newel post?

Newel post half—Used on landings where the end of the balustrade meets a wall, a half newel post is the ideal way to finish off the balustrade, adding extra strength and a smart finish. Half posts attach directly to the wall and sit flush against it.

What height do you cut a newel post?

The height to the top of the post is 950mm above the landing. The height from the top of the post to the bottom of the turning is 725mm. The drilled base length will depend upon the depth of your string and how far you wish the post to protrude down below the stairs.

What is a half box newel post?

Half Newels are designed to be used where handrail terminates against a wall, creating a continuity of design throughout your handrail system and they match the other newels used on your stair way.

How do you fix a half newel post?



Drill through the drywall with a 1/2-inch drill bit. Insert a 1/2-inch drywall insert, place the adhesive on the half-newel and then screw the newel to the insert. Finish the newel post and furniture buttons with stain or paint before installing them.

Do you have to have a newel post?

Further, for code-compliance, a newel post is necessary on balconies where the length of the handrail is eight feet or longer. Therefore, if you have a sixteen-foot balcony, you will need three newel posts, one at the beginning, one in the middle, and one at the end.

How do you replace half newel?

What alternatives are there to half newel posts? If there isn’t enough space against the wall to fit a half newel post, you can simply run the handrail directly into the wall. It you are using spindles you can either fit a full spindles or slice a spindle in half length ways to sit against the wall.

Can you replace a newel post?



To replace a newel it takes very little skill and most people who can handle basic DIY are capable of changing one. To start with you must remove the existing newel, the new post should then be cut to length.

How are newel posts attached?

Basically you will be installed an access hole on the side of the newel with the 1-1/2″ drill bit and then drilling a 5/8″ hole up from the bottom. This allows you to set the newel post down over the lag and tighten it down with the washer and nut. Step 2 – Screw the lag bolt into the floor.

How do you install a solid newel post?

Quote from the video:
Quote from Youtube video: And drilled an eighth inch deep hole into the joist another beautiful thing about all this is that the pilot hole should be close to plumb.

How do you repair newel post stairs?

Quote from the video:
Quote from Youtube video: Of course the size these notches will have to be made for your stairway. But just remember the centerline of the balustrade must line up with the center line of the newel.