Yes, that’s fine. They don’t need to be the same.

How do you wire multiple lights from one power source?

You can do this light switch wiring in one of two ways. The most common is to daisy-chain the light fixtures by connecting them to each other and hooking the first one up to the switch. The other way to wire multiple lights to one switch is to connect all of them directly to the switch in a “home run” configuration.

How many LED shop lights can you connect together?

10 LED shop lights

Up to 10 LED shop lights/garage lights can be linked together using the included butt connector or 5.25-foot interconnect cable. Separate 9.5- and 4.5-inch interconnect cables are also available (sold separately).

Can you hardwire a LED Shop light?

Quote from the video:
Quote from Youtube video: You're gonna see a little black and a white wire. Inside. That's what we're gonna use to actually hardwire this light into the ceiling where i've ran all my electrical.

How do I connect multiple 12v LED lights to one switch?

Quote from the video:
Quote from Youtube video: The easiest way of running more lights to a circuit with piggyback terminals these terminals can be used to splice in multiple lights to your positive cable as shown in our diagram.

How many LED lights can you daisy chain?

For example, if you choose a 120-volt power supply for daisy-chaining 10-watt LED tube lights, you will be able to connect 12 LEDs. However, to sail on the safer side, make sure that you do not connect more than seven tube lights to a power supply.

How many can lights on one circuit?

There is no limit to the number of lights on a circuit. The load of the fixtures is what determines how many lights a circuit can accommodate. A conventional 15A circuit can have up to 1400W of lighting loads connected to it. A 1400 Watts lighting load can accommodate one 1400W fixture or fourteen 100W fixtures.

How many LED lights can you put on a 20 amp circuit?

Maximum Lights Per Circuit



Technically, you can install 13 outlets or lights on a 20-amp CB, but you can only put ten lights per circuit due to the 80% rule of maximum continuous load.

What happens if you string too many lights together?

Because light strings have a maximum wattage capacity, which is why many string lights come with a little fuse just in case you connect too many together at once. The fuse is designed to blow so you don’t overload and damage your Christmas lights.

How do you join LED string lights together?

Quote from the video:
Quote from Youtube video: You feel it you kind of miss it. And then what you're gonna do is you're gonna open it. Up. You're gonna slide on one side underneath there like so pull that connect it down. Get your other. Piece.

Can I connect 2 LED strips together?

Quote from the video:
Quote from Youtube video: You may need to solder two together directly. But more likely you'll probably just want to add a separate lead for stretches you won't want lights but need to keep a line running.

Can you overlap LED lights?

C) Make sure the voltage marked on your light strip matches the LED Driver. D) Do not overlap this product as the overlapping may cause the flexible light to overheat and melt or ignite. E) Do not cover this product as the covering may cause the flexible light to overheat and melt or ignite.

Can you wire LED strip lights in parallel?

The alternative to connecting multiple LED strip sections together is to wire them in “parallel.” This method involves creating independent runs of LED strip sections, each of which is wired directly to the power source.

Can LED lights be wired in series?

LEDs wired in series are connected end to end (the negative electrode of the first LED connects to the positive electrode of the second LED and the negative electrode of the second LED connects to the positive electrode of the third LED and so on and so on…).

Can you power LED strip from both ends?

To avoid voltage drop on longer strips, it is possible to wire a strip from both ends. IMPORTANT: ONLY POWER LED STRIP FROM BOTH ENDS ON THE SAME POWER SUPPLY. NEVER USE MORE THAN ONE POWER SUPPLY WITH THIS CONFIGURATION.

Should LEDs be in parallel or series?

series-parallel

Generally speaking, most LED lighting uses a series-parallel combination. Ideally, for reliability and lighting consistency, it would be best to have one strip of LEDs all wired in series to a constant current driver.

What happens when an LED is directly connected to a power supply?

When LED is connected to a power supply with a voltage higher than its forward voltage, a current limiting resistor is connected in series with the LED. The current limiting resistor limits the current for the LED and regulates the difference in voltage drops between the LED and the power supply.

Do you need a resistor for every LED in parallel?

Quote from the video:
Quote from Youtube video: In series it's exactly the same you need just one resistor power supply.