If you have studs attached to the existing wall and those studs are attached using long enough screws to attach to the studs behind, that’s perfectly fine. In fact, removing the existing drywall will cause more problems than not.

Can you add a wall without removing drywall?

So long as you build a solid frame and connect it well, once installed there is really no chance of existing drywall being “crushed” by the frame. To crush the connecting drywall after installation, you’d need a very serious lateral force which is enough to flex or shift the frame itself.

How do you attach a new wall to an existing wall?

Apply a level to make sure the wall is exactly vertical. Shim any gaps between the new wall and the ceiling. Nail or screw the wall to the floor and to the ceiling joists. If the new wall aligns with a stud on the adjoining wall, attach it there as well.

Can you reuse Sheetrock?

No matter how careful you are when removing drywall from a wall or ceiling, it will never be in “as new” condition. You may be able salvage it for reuse, however, if you are systematic in your approach, and your success will depend on how it is attached and whether it has been taped.

Does drywall need to go to the floor?

It might sound counter intuitive at first to leave space between your floor and your wall, but you should always leave a ½ inch to ⅝ inch gap between drywall and the floor.

How do you build an interior wall in a finished basement?

Quote from Youtube video: You can measure that gap right here. And start to build our wall. And one other thing we need to do is we need to expose the floor. So we can nailed our wall down.

How do you join two walls?

Quote from the video:
Quote from Youtube video: And have an inch-and-a-half nailer on each side for the drywall or paneling this one works great takes 3 studs. Though. That was the fastest video I think I've ever made. So.

Should basement drywall touch the floor?

Drywall should NOT touch the floor. Allow for floor and wall expansion without cracking the drywall by keeping a 1/2-inch (1.27-cm) space between them. This space also aids in preventing moisture from seeping if the floor floods.

Should drywall touch the ceiling?

Note that drywall on the wall should support the ceiling drywall, meaning you install the ceiling first, and the wall is installed tight against the ceiling. For the bottom piece, you use a roll lifter under the drywall to lift it up and give you a tight fit to the board above it.

What should I put between drywall and concrete?

The solution is covering concrete with a vapor barrier, which acts like a resistant cell membrane instead. With a shield in place, the drywall is safe. Typically, a stud wall is then installed against the concrete, but furring strips are quick, easy and take up less space.

How do you separate basement spaces?

Here are seven ways to divide your basement into separate rooms:

  1. Add permanent walls.
  2. Add a sliding door.
  3. Bring in curtains.
  4. Get folding screens.
  5. Use a bookshelf.
  6. Get some beads or a wall hanging.
  7. Get creative with furniture arrangements.

Can you add onto an existing basement?

Yes, you can. Extending the basement past the house into your yard can be done. Experts suggest doing the extension by digging in the yard towards the house or digging via the existing basement.

What is the cheapest way to finish a basement wall?

Paneling can be used as an inexpensive way to finish you basement walls or ceiling. Use a strong adhesive to put strips of wood on your concrete basement walls, and then use wood screws that match your paneling to attach the paneling to the wood strips.

How do you finish a basement without framing?

The simplest solution on how to finish a basement without framing is to go with paint. You can clean your basement walls, then apply multiple coats of high quality paint.

Should you seal basement walls before finishing?

Water issues can cause serious damage and ruin your investment. Before finishing the basement, deep-seal your concrete against water seepage, water vapor, and soil gases like radon.

What can I use instead of drywall in my basement?

Finishing Basement Walls Without Drywall: Options and…

  • Paint.
  • Basement Panels.
  • Wood Fiberboard.
  • Fabric.
  • Vinyl and Wallpaper.
  • Stone Veneer.
  • Pargeting.
  • Exposed Brick.

Do I need mold resistant drywall in basement?

Due to the often damp conditions of the basement, be sure to choose sheetrock that is at least moisture-resistant (often call greenboard) but be on the lookout for products that are specifically resistant to mold and mildew (some kinds of purple board).