No. Those holders give virtually no torsional support. Your gate will tear it right down.
Can you attach gate to concrete post?
You can attach a gate to a concrete fence post. The easiest way to attach a gate to a concrete post is by using a hinge known as the gate screw hook. Attaching a gate to a concrete post requires proper drilling and anchoring. This ensures long-term stability between the gate and post.
How do you hang a gate on a 4×4 post?
Quote from Youtube video: It's taken a measurement from the bottom of our first hinge to the bottom of our second hinge we've made a mark and now we're going to drill. Our hole make sure you're in alignment.
What size post do I need to hang a gate?
A solid anchor post cemented in place is a good start
First, it is important to use an anchor post or pipe large enough to hold the gate. To hang a 14- to 16-foot gate ,use a wood post six to eight inches in diameter, or a six-inch diameter pipe.
Do gate posts need to be set in concrete?
Either way, concrete or solidly tamped dirt, your corners and gate posts, if braced properly, should be fine. Using a gate wheel on the longer posts also helps keep it all level, if you have level ground for it to set on. I would advise against using concrete if you can avoid it.
How do you fit a garden gate to a concrete post?
Quote from the video:
Quote from Youtube video: There are a few ways to do this but i find the easiest and the strongest. Way is to just use masonry screws i'm using a torx. Head high strength masonry screw seven millimeter by ninety millimeter.
Can you drill into concrete posts?
It is possible to drill into a concrete fence post. With the proper tools and approach, it’s easier than you might think. There are some necessary things to take into consideration before you start drilling, such as the type of drills you will need and the specifications of your posts.
How do you support a heavy gate?
Pressure-treated six-by-six wood posts set in concrete on each side of the driveway should support a gate that’s not unusually wide; steel posts in concrete are stronger. One post is for the hinges and the opposite post is for the gate latch, which adds some support when the gate is closed.
How do you attach a gate to a post?
Quote from the video:
Quote from Youtube video: What we have to do now is put on the hinges. So you see I can lay them out so they're in the center of this 2×4 rail to pre-drill the holes.
How do you support a gate?
Quote from the video:
Quote from Youtube video: Up you have a tension brace and a compression brace. This right here is a compression brace. But just for good measure over time. We don't want this gate to sag.
How do I make a gate that won’t sag?
Quote from the video:
Quote from Youtube video: I use tight bond you can use Elmer's or any other brand. I just happen to have tight bond.
How do you brace a gate to sag?
Quote from the video:
Quote from Youtube video: Across you know two braces one in there and one in there or what i usually do is one there right down at the bottom corner.
Do you need a cross brace for a gate?
Over time a wooden gate will tend to sag. So you need a cross brace. If you are building the cross brace using wood, the cross brace should be in compression. So the cross brace will go from the corner with the bottom hinge to the top corner on the other side.
What angle should a gate brace be?
If your cross-brace is at an angle greater than 45 degrees from the base of the gate, your door will support itself and last a lot longer. Also of importance is that an angle less than 45 degrees will render your cross-brace totally ineffective, and the weight of the gate will place undue stress on the hinges.
How do I reinforce a gate post?
Quote from the video:
Quote from Youtube video: And what a drive for is you use it on best clothes replacements mail boxes things like that you just dump the dry dry concrete into the hole.
How do you hang a heavy fence gate?
Quote from the video:
Quote from Youtube video: And you basically just two wedges one on top of the other you sit the gate on these wedges. You push the two wedges together and it'll lift the gate up and you pull the two edge of the path.
What type of hinge do I need for a gate?
With Tee hinges, you’ll want to use a hinge length of at least half the width of the gate you’re hanging. For instance, a 1000mm wide gate will need a 500mm Tee hinge. For any gates above 2100mm, a third hinge should be added to support the additional weight.
What causes a gate to sag?
In general, there are only a few reasons why a gate would sag. Either the gate material is warped, its hinges are not correctly in place, the gate is lacking structure components or its posts are no longer parallel with one another.
