Can you use a Fernco on copper pipe?
The dimensional flexibility of Fernco couplings ensures leak-proof pipe seals on virtually any pipe material: plastic, cast iron, asbestos cement, clay, concrete, steel, copper and ductile iron.
Can you use flexible pipe for drainage?
The Flexible Drain Pipe system is a revolutionary landscape drainage system for residential and commercial use and the newest brand of product for Rain Bird. This unique pipe expands and flexes, making it perfect for tight spaces and curvy places.
Can you replace copper pipe with flexible?
While copper pipes and fittings are still common, many professional plumbers now use flexible PEX for all new construction and for most repairs and extensions to existing copper systems.
How do you sweat 2 inch copper pipes?
Quote from the video:
Quote from Youtube video: Now let me start by explaining why I use the method I use when soldering 2 inch piping. I found that heating the bottom half and then finishing by the top half gives me the best results.
How do you tie a copper drain?
Quote from the video:
Quote from Youtube video: You're able to tighten them up and that's how you adopt from inch-and-a-half copper over 2 inch and a half abs PVC cast iron something like that this really helps with older home remodels.
How much pressure can a 2 Fernco handle?
Maximum test pressure: 4.3 PSI (29.6KPA) Maximum operating temperature: 140º F non-consistent.
Is Flex drain any good?
5.0 out of 5 stars Value for money. This product is excellent for french drains and general drainage installation. I like that it is flexible and therefore able to be installed in serpentine areas.
Are flexible waste pipes any good?
Having to use a flexible waste is just poor plumbing design. In MOST cases. I have had to use a couple recently. The first was to get a bathroom basin waste back a very short distance – joints would not have done it and I have kept it near vertical so very little will catch in the folds.
How strong is flex pipe?
By its nature, flex pipe isn’t very strong and can be compressed/misshapen by anyone of average strength with their bare hands. Depending on soil conditions, one square foot of dirt can weigh anywhere between 75 – 120 pounds, with a full square yard of soil weighing up to one ton or more.
How hard is it to sweat copper pipe?
Soldering copper water supply lines is not a difficult skill. Even a rookie can learn to solder leak-proof joints in 30 minutes. The process is simple—if you follow a few basic guidelines.
Can copper pipe be Unsoldered?
Unsoldering the copper joint can be done by applying high heat over the copper coupling or connection that needs to be detached. This process takes several steps to finish. First, you need to have the necessary tools to get the work done easily and accurately.
What can I use to sweat copper pipes?
The torch needed for soldering copper can be propane or MAPP gas (methylacetylene-propadiene propane). MAPP gas comes in a yellow tank and propane comes in a blue tank. MAPP gas, usually a bit more expensive, gets much hotter than propane, so heats the pipe faster.
Can you sweat a copper pipe with water in it?
Stop the water with a pipe plug
Don’t try to solder pipes with water in them. When you’re repairing or tying in to existing copper pipes, it’s common to find a small amount of water in them even after you close the valve and drain the pipes.
What is a sweat tee plumbing?
Sweat fittings have a nonthreaded joint with a diameter slightly larger than the pipe. They slip onto the pipe, then when hot solder is applied, the solder seeps into the gap and fuses the fitting to the pipe.
Is sweating and soldering the same thing?
“Sweating” and “soldering” are synonymous terms used to describe the process of using heat and solder to join copper pipe and fittings to one another. You can tell your neighbor you’re heading downstairs to “solder” a joint—but “sweating” makes you sound much more worldly and DIY hip.
Can copper pipe be overheated?
Overheating is a major problem when brazing or soldering copper pipe because the flux will burn (become oxidized), stop working, and become a barrier to tinning. In addition, a heavy oxide can be formed on the pipe itself, preventing a bond from forming between the filler metal and the pipe surface.
Why is copper called sweat?
The walls of copper pipe, however, are too thin and soft to be threaded, so a different sort of fitting is used, called a sweat fitting. It’s called that because the process of joining the various elements using solder involves heating them with a propane torch until they seem to sweat.
How do you solder copper pipes to overheat?
How to Solder Copper Pipe Joints
- Buy a self-lighting torch. …
- Use a good-quality tubing cutter. …
- Use a steel brush for complete cleaning of pipes and fittings. …
- Apply tinning flux rather than regular flux. …
- Assemble the pipes, then solder the joints all at once. …
- Heat the joint just enough to melt the solder.
Why do plumbers use bread?
Grab a piece of white bread and shove it down as far as you can inside the pipe. The bread will stop the leak while you solder the fitting and will then (eventually) dissolve inside the pipe.
What kind of solder do you use for copper pipes?
What Type of Solder is Used for Copper Pipe? Lead free solder is best for copper pipes carrying drinking water. It will be free of elements you don’t want entering your drinking water. However it will require a higher melting point than a 50/50 solder.
