Can you safely put a different size orifice on a gas stove burner?

What size hole is a natural gas orifice?

Natural gas pilot orifice sizes typically vary from approximately 0.014 to 0.026 (inches diameter). Examples include 0.026′′ for a commercial cook- ing appliance pilot (1,835 Btu/hr at 4′′ pressure), and 0.018′′ for a natural gas water heater pilot (879 Btu/hr at 4′′ pressure).

What is the difference in orifice size between propane and natural gas?

Propane and Natural Gas Are Supplied at Different Pressures



Cooktop burners typically supply about 40,000 BTUs per hour. A propane stove orifice size is about 0.082 inches (drill size 45), but the valve on a similar stove that uses natural gas needs an orifice that is almost 0.125 inches (drill size 35).

Are all propane orifice the same?

The orifice diameter of these tiny little parts is different between natural gas and propane or LP gas. This means that you will need to change the orifice fittings to match the fuel you intend to use.

What type gas requires a larger orifice?

The reason for this is because natural gas orifices are larger than propane orifices strictly because of gas service pressure.

How do I know what size orifice I need?

If you don’t know what size that tiny hole is, spend $4 on a small drill bit set and use the shank end (the opposite end from the cutting end) as a gauge pin. The largest one that will fit in the hole is your orifice size. Then you can use the chart to calculate the maximum heat output of each burner.

How do I know my orifice size?

Quote from the video:
Quote from Youtube video: The first step is to take the btu load and divide it by the number of burners. One hundred thousand btus divided by four burners equals twenty five thousand btus per burner.

What happens if you run propane through a natural gas orifice?

Running propane through an orifice designed for natural gas and lower pressure will result in an overly large flame and soot. The flame will be bigger and may cause damage and even an explosion. This is because the orifice jet designed for natural gas is larger than the one for propane.

What is the orifice size for propane?

A propane stove orifice size is about 0.082 inches (drill size 45), but the valve on a similar stove that uses natural gas needs an orifice that is almost 0.125 inches (drill size 35).

Is natural gas interchangeable with propane?

For the home, you will find appliances that work on either natural gas or propane. The two are not interchangeable; each fuel source requires special gas utilization fittings. If you want to switch between the two, you’ll need a conversion kit for the appliances’ manufacturer for the installation process.

Can you convert gas stove to propane?

Most, but not all, appliances can be converted from natural gas to propane. The biggest sticking point is that natural gas is kept at a lower pressure, and some appliances can’t handle the higher pressure of propane even with adjustments.

Are all natural gas orifices the same?

Gas types are not interchangeable. Natural Gas orifices will have a larger hole as it is a lower pressure gas and Propane is a compressed gas and the orifices will have a smaller hole. They are not interchangeable. You never want to use an orifice that is drilled for Natural Gas on Propane or Propane for Natural Gas.

What is a natural gas orifice?

Orifices are responsible for the amount of gas that flows into the burners. Orifices are brass fittings that screw into (spud) or onto (hood) valves. These orifices will have various hole sizes as they determine the gas type either Propane or Natural Gas.

What is orifice size?

The orifice diameter is the internal opening of the valve and is used to calculate the flow capacity of the valve. Metric or English makes no difference. It’s the inside hole. The inlet size is the interface or the size/type of the threads where you attach the valve.

What size is a 54 orifice?

Conversion Chart

How do I make an orifice?

Steps required to design an orifice plate or orifice plate flow meter:

1. Identify the physical attributes of the piping system. …
2. Identify and accumulate data on process flow conditions. …
3. Identify and accumulate information on other requirements of the flow meter.