How do you wire a condensate pump?
Quote from the video:
Quote from Youtube video: The wires coming around. And here's the other end of the wiring my red and my white. So here's my red from my air handler. Put that one right here. Here's my red from my thermostat.
Can you hardwire a condensate pump?
Condensate Pump Wiring
In either case, the outlet should be on a dedicated circuit. Some pumps must be hardwired and come with a stripped wire cord end or other type of connection. These power connections must be made in a junction box and must comply with the National Electrical Code.
How do you wire a Little Giant condensate pump?
Quote from the video:
Quote from Youtube video: Now you can remove the pump wires by unscrewing the moretz. And untwisting them from the furnace power wires. And just pull the cord. Out. Get your new pump i'm using a little giant.
Does a condensate pump need a dedicated circuit?
a SINGLE RECEPTACLE type electrical outlet dedicated to just the condensate pump, and the GFCI protection otherwise required (recommended too) can be forgiven – you will want to confirm this approach with your local electrical inspector.
Where do you plug in a condensate pump?
Quote from the video:
Quote from Youtube video: So we're just going to hook it all back up. This here's the discharge port that goes out so we're just going to replace this a real simple replacement on this one. Hold the discharge port loose.
How do you install a condensate pump with a safety switch?
Quote from the video:
Quote from Youtube video: First thing you want to do is you want to take your nip. I'm going to put it right here inside your unit. Then you're going to take a little glue and you put glue on here.
How do you wire a condensate overflow switch?
Quote from the video:
Quote from Youtube video: I'm just going to take that one out hook one side of it up to that hook. This side up to that you know basically that way power is coming out of the wire here running down to the switch.
What is a safety switch on a condensate pump?
The condensate overflow switch serves to prevent the pan from overflowing if the AC drain stops working properly. The switch is activated when the level of the water in the pan comes above a certain point, causing the switch mechanism to trip/float to rise.
How do you hook up a condensate pump to a dehumidifier?
Quote from the video:
Quote from Youtube video: Great first thing i'll do is clean both the pipe. And the fitting. And then i take some solvent cement. And repeat the same. Step. Hold it for a quick count.
Does a pump need to be on a GFCI?
Later versions of the NEC require that sump pumps be placed on a GFCI protected circuit.
Does a condensate pump need a trap?
Yes, if the pipe extends below the water line inside of a pump, that is a trap and yes, if someone adds another trap it won’t work very good. Also, the furnace has a built in condensate trap inside of it, so you need to be aware of that too.
Does a condensate pump run all the time?
Condensate Pump Floats
When the float reaches a certain point, a switch is triggered which sends the water outside or to a drain. If that float gets hung when the water level rises and can’t slip back down into its natural position, the condensate pump will run continuously.
Can you wire condensate pump to mini split?
Condensate pumps require line-voltage power that can be wired from the mini-split electrical terminal. Some pump brands might also have the ability to shut down the mini-split equipment if an evaporator pan overflow event begins to occur.
Do condensate pumps have a check valve?
For use with Condensate Pumps
A check valve keeps water from draining back into the pump which can cause the pump to short cycle. This small accessory can extend the life of the motor.
Can I run furnace without condensate pump?
All condensate drains go into a trap. The condensate trap is absolutely mandatory for a high-efficiency gas furnace. Since the drain taps into the exhaust system, leaving it open to the air would allow for a potential exhaust/flue gas leak in the living space, which is a big no-no.
Does a high efficiency furnace need a condensate pump?
The purpose of the second heat exchanger is to get more heat from the exhaust before it is vented. As a result, high-efficiency furnaces require condensate drains because their exhaust gases cool enough to allow the moisture in them to condense from steam into water droplets.
Should a condensate pump have water in it?
Make sure you don’t run the condensate pump without any water in the reservoir since this can damage the device. If water comes out of the drain hose then you know that the hose is not clogged. If the water doesn’t come out of the drain hose then it’s possible that there is a clog.
Does condensate pump work with furnace?
But many older homes don’t have a floor drain next to the furnace. So furnace installers mount a condensate pump right on the furnace and route the drain line to a far-off sink or floor drain. If that condenser pump fails, the water overflows the pump and spills onto the floor.
How do you install a condensate pump on a furnace?
Quote from the video:
Quote from Youtube video: Now connect the inlet pipe and set the pump into place next attach the discharge tube to the barbed fitting. If your old pump used a safety switch then connect the wires to the new switch.
Why does a furnace need a condensate pump?
Condensate pumps are used to effectively direct and remove excess water from high efficiency furnaces (as well as humidifiers and A/C units). The pump takes the place of hoses that can and do rupture, and seamlessly transfers water to the appropriate drainage pipe.
