1 Answer

  • Mainly the cause of cracks comes from moisture (Water) and oil spilled on your floor. This moisture if you just spray the coating on it it will make your coating have microbubbles and leaving you with cracks.
  • Or the concrete/floor is not porous as stated in the product application manual.

Is it normal to have cracks in garage floor?

It is very normal for the garage floor to have cracks in them. You will see cracks in most garage floors. Unless there is a structural defect in the floor, there is no need to worry about the cracks. You can fix the cracks easily if you like.

How long do polyaspartic floors last?





10-20 years

If you are wondering how long a polyaspartic floor coating lasts, that will depend on how much wear and tear it receives and how well it is applied. However, a good rule of thumb is 10-20 years depending on the traffic on it and installation.

How do you repair a polyaspartic?

Damaged polyaspartic coatings can be repaired by smoothing, roughening, and applying another coat of polyaspartic. Contact the manufacturer regarding surface preparation and application recommendations. However, if the floor’s exposure conditions do not improve, the abrasion damage will reoccur.

Can you epoxy a garage floor with cracks?

Epoxy coatings cannot withstand the stresses associated with concrete cracks due to settling, dry shrinkage or other factors. Don’t let the fear of cracks keep you from enjoying the benefits of epoxy; with a little prep and repair work, you can move forward with your epoxy project.

What causes cracks in concrete garage floor?





They are caused by improper troweling and placement of the concrete; the thin top layer of concrete dries out faster than the rest of the concrete, thus these hairline cracks. They are generally of no concern when it comes to structural integrity.

When should I be concerned about my garage crack?

You can tell if cracks in your garage floor are serious if they have an opening that measures 1/8-inch or more in width, and/or if one side of the crack is higher than the other.

Can you recoat polyaspartic?

Deglazing the Polyaspartic Floor Coating

Deglazing and recoating is a time-saving way to improve the look of your floor, but this can only be done if the existing coating is in good condition and isn’t seriously cracked, chipped, or peeling.

Does polyaspartic bond to concrete?



Because of the way that polyaspartic coatings bond to concrete, they have higher strength and flexibility than epoxies, making them great for high traffic areas.

What will polyaspartic stick to?

What types of environments can Polyaspartic Coatings be applied? Generally, any type of an environment where a resinous concrete floor coating is called for, a polyaspartic coating system may be used. This includes heavy traffic industrial and commercial flooring as well as residential garage floor coatings.

How long does it take for polyaspartic to dry?

Polyaspartic coatings are applied professionally, usually with a squeegee or roller and are extremely quick to dry – often within a few hours.

Can polyaspartic be applied over epoxy?



Can Polyaspartic Coatings be used over an Epoxy Coating? Yes, Polyaspartic coatings exhibit superior inter-coat adhesion with epoxy coatings. For old epoxy floor coatings that are still well adhered to the substrate, an installer can apply a new polyaspartic top-coat over that area.

Does polyaspartic yellow?

About Polyaspartic Flooring

In addition, polyaspartic garage floor coatings are resistant to yellowing, fading, and peeling. This is because they are made with aliphatic compounds, which do not yellow in the sun or emit any volatile compounds into the air.

Does polyaspartic stain?

Stain Resistant



Polyaspartic coatings are smooth, watertight, and stain-resistant. Their smooth surface does not scrape dirt from shoes and leaves no room for dust particles to hide. This makes cleaning floors easy and quick. It is also chemical resistant.

What is better epoxy or polyaspartic?

Epoxy is very durable, but it is still vulnerable to abrasion. Polyaspartic, meanwhile, is more flexible, and won’t chip, scratch or scuff. It’s definitely more durable.

How do you clean polyaspartic floors?

Regular sweeping is essential.

Use a soft-bristled broom or microfiber dust mop to sweep your polyaspartic floors. Clearing them of dust and other debris will help reduce wear and tear. This will also ensure they’ll remain free of cosmetic damage such as scratches.

How do you remove Rust Oleum RockSolid?



Apply RockSolid Heavy Duty Cleaner to the entire floor and allow it to soak into the surface for 5-10 minutes, misting the surface as needed to keep it damp. Work the product into the surface with a stiff bristle brush or broom. Rinse the surface thoroughly with water or power wash to remove all cleaner residue.

Can you use Pine Sol on epoxy floors?

Regular Care:

Even though epoxy is a durable material, small bits of dirt can become embedded in the epoxy if not removed properly and frequently. Mix an all-purpose cleaning product such as Pine-Sol or Mr. Clean and mix it according to manufacturer’s directions in a bucket with warm (never hot) water.