How do you cut a toilet supply line?
Quote from the video:
This should easily unscrew by hand once the nut becomes loose gently pull the water supply line to the side. Now pull the hard water supply line straight out of the top of the valve.
How do you shorten water supply lines?
A pair of tin-snips will cut the line to the proper size. The connections use compression fittings. Installation requires inserting one end into the lower pipe and cutting the top end to fit the upper pipe. You slide the compression fittings, which include a plastic washer and a nut, onto the pipe.
What size are bathroom sink supply lines?
Standard Sink Supply Line Size
The branch lines, which are the ones that feed individual fixtures, are 1/2 inch in diameter. The 1/2-inch supply pipes that come to the sink each terminate with a shutoff valve, and this valve is one of the two factors that determine the connector size on the faucet hose.
How do you replace a bathroom faucet supply line?
Quote from the video:
Stop. At this point I'm going to loosen my connections here underneath my sink for my old faucet. Now we're gonna simply remove our old faucet. Here's my replacement faucet.
How do you replace a rigid toilet supply line?
Quote from the video:
Valve. Once the rigid pipe is removed grab your flexible. Hose. Take your wrench. And connect the bottom of the flexible steel hose to the angle valve at the wall by turning. Clockwise.
Can you run PEX to a toilet?
Quote from the video:
You will need a half inch shutoff valve a half inch crimping ring your crimper with a half inch die. Inside. So what you want to do is either tee off your main line coming in of your cold.
How do you move water lines in a bathroom?
Quote from the video:
And so I'm gonna run six new lines. So every single one gets their own feed off the two in the basement. Right now I got a drill a hole through the floor. So I know where to run those pipes.
How do I shorten a delta supply line?
Quote from the video:
The cleanest way to make the cut is with a plastic tubing cutter which you can pick up at your local home improvement store make a straight cut along the mark in the tubing push.
Are toilet and faucet supply lines the same?
A faucet, toilet, and refrigerator’s ice maker use a similar water supply line. A refrigerator’s ice maker uses 1/4-inch tubing with 1/4-inch compression fittings on both ends.
How do you remove a supply line from a faucet?
Quote from the video:
Line and put it right on top of the nut and then you can turn it counterclockwise to loosen in that that's up against the bottom of the faucet.
How do I fix a leaky sink supply line?
Quote from the video:
So that's all it took to fix this plumbing supply leak if you have other home improvement questions visit us at home Edition plus calm today.
How do you connect a copper supply tube to a faucet?
Quote from the video:
It's actually compression connections it has a brass nut a brass ring called a ferrule that compresses around the copper pipe. And once we bring those together and tighten it up it's a watertight.
Do you use Teflon tape on water supply lines?
Most faucets will have hot and cold water supply lines attached, so you just need to connect them to the appropriate water supply line. You may need to use Teflon tape (aka plumber’s tape) for this part, which is used to seal and lubricate threaded pipe joints.
Should I use plumbers tape on supply lines?
Quote from the video:
You don't use teflon tape because what you do is you end up putting this on tightening it up and then the little spigot tightens up on the gasket.
How do you cut copper pipe?
Quote from the video:
Using the tubing cutter or pipe cutter me show you how it's done set the tubing cutter on the pipe. The pipe is resting on those two rollers.
How do you cut a tube?
Quote from the video:
Then hold on to the end of your pipe with a plier so that it won't spin then spin the pipe cutter every time you spin it around go ahead and tighten it.
How do you cut copper tubing without a pipe cutter?
Using a Hacksaw
The hacksaw is a type of hand-driven saw with a very thin blade. The saw blade’s teeth are very small, so they easily cut into the copper pipe’s surface. However, like using the circular saw/angle grinder, the cut’s angle is important if the pipe will be reused.
