Where is the diverter in my kitchen faucet?

The diverter assembly is located in the back of the faucet body, facing away from you sink. It is a small black part that is inserted into a hole in the faucet body (Fig. 4). Using a needle nose pliers, pull out the old diverter assembly by grabbing on the “fins” of the assembly.

Do all kitchen faucets have a diverter?





Besides kitchen faucets, other faucets also have diverters. A tub and shower faucet, for example, has a diverter to redirect water from the showerhead to the tub spout. The diverter is usually located on the tub spout or as a lever or button on the faucet.

How do you remove a kitchen faucet diverter valve?

Quote from the video:
Quote from Youtube video: This particular one has a set screw that mounts in the front with an allen wrench some of them have a button on top that you to remove that handle. And just a basic screw.

How does faucet diverter work?

The diverter inside your kitchen faucet redirects the water from the faucet spout to your faucet sprayer when you press the sprayer trigger. When you squeeze the trigger, the water pressure drops to engage the diverter. This stops the water flow at the spout and moves it to the sprayer.

Where is the diverter valve?

It’s usually a lever that’s situated behind the bath taps that you can pull up or push down. System and conventional boilers don’t require a diverter valve.

How do you fix a diverter faucet?





Repairing the Shower Diverter

  1. Shut off the supply of water to your shower.
  2. Seal your drain with tape so that small screws or other vital parts are not lost down the drainpipe.
  3. Tighten the screws behind the faceplate of the diverter valve. …
  4. Disassemble the shower diverter. …
  5. Change the diverter.

How do you change a diverter valve?

Diverter Valve on a Spigot

  1. Unscrew the set screw. See how the spigot is attached to the wall. …
  2. Unscrew spigot from the wall. Be careful! …
  3. Wash Supply Pipe. Make sure that you clean off any bits of gunk from the supply pipe. …
  4. Replace new spout on the copper pipe. …
  5. Test it and make sure it works!


What is a diverter valve?

Diverter valves switch the flow of water between the tub faucet and the showerhead. Water flows directly through the faucet and into the bathtub when the valve is open. When the valve is closed, water pressure forces the water to run upward to the showerhead.

How do I clean a diverter spout?



Press and depress the diverter valve a few times, then spray an oil-based cooking spray onto the plunger where visible. Pump the diverter valve a few more times. This lubricant can help get into stuck parts and provide enough slickness to get them moving again. Cooking spray is organic and safe for use.

Why does my kitchen faucet thump when I turn it on?

If you hear a rapid clunking noise when you turn on the faucet that could mean air is trapped in your pipes. Try turning on all of your home’s faucets at once and then flushing all of your toilets. Wait for five minutes or so and give the water time to push out the air.

How does a push button diverter work?

It’s designed to divert water up into the showerhead instead of pouring out of the tub spout. Typically, you’ll adjust the faucet to your preferred water temperature before you activate the diverter to send water to the showerhead or bathtub.

How does a 3 way diverter valve work?



The three-way diverter allows you to alternate between any of your selected shower outputs by directing the water from the shower head to each additional accessory, one at a time. The diverter will not adjust the water temperature or turn the water off or on. All rough-in work should be completed by a professional.

How do you replace a Kohler push button diverter?

Quote from the video:
Quote from Youtube video: So all right so you just thread the push stop valve on here you'll get the small allen wrench and there's just going to be two screws that you'll just. Tighten you want to make sure it's pretty tight.

How do you fix a tub diverter valve?

Quote from the video:
Quote from Youtube video: Set the screw in a safe location. And we can pull the cap off now see how easy that was chances are yours might not be that easy yours might be very rusted corroded and oxidized.

How do I know if my diverter valve is faulty?

A diverter valve may be faulty if the hot water taps still work while the radiators do not turn on. Another sign of a faulty diverter valve is if you only can only get lukewarm water from your taps.

What is a tub spout diverter?



A bath and shower diverter is a device that diverts the flow of water either toward the tub spout (i.e., to the bathtub) or toward the showerhead. This product is commonly found in bathtubs equipped with a showerhead, such as in residential bathrooms and private commercial restrooms found in hotels.

Why does my shower head and faucet run at the same time?

Most likely you are experiencing “shower-rise,” where the water can’t get out of the spout as fast as it flows through the valve. This causes the water to back up and come out the shower head.

What does a shower diverter look like?

Quote from the video:
Quote from Youtube video: Comes in from the left cold. Water from the right the two are mixed in the valve. And will either go up to the showerhead or down to a tub spout a diverter directs which way the water goes.

Why is water coming out of faucet when shower is on?

Why Your Faucet is Leaking when the Shower is On: The reason your faucet leaks when all of the water is supposed to be going up to the showerhead is a faulty diverter valve. This is the part that diverts the water from the tub spout up to the showerhead. As we said before, these can be fixed!