Yes you do. Add another dotted line to the first part of your dotted line on you main stack. Also my local inspector would not let me share a drain for shower, sink, and toilet.
Does every drain need a vent?
Without getting too far into building science, a general plumbing rule of thumb is that every drain needs a trap, and every trap needs a vent. All those traps and drains are designed to prevent sewer gas from entering your home.
Does a washing machine drain need a vent?
All plumbing fixtures—including washing machines—must be vented. Improperly vented drains can be sluggish and noisy, and can emit hazardous fumes. Properly vented drains allow the P-trap to do its job: prevent sewer gases from escaping into your home.
Do all bathroom fixtures need to be vented?
Whether you’re putting in a tub, toilet, sink, or floor drain, they all need a plumbing vent on the drain to make it work properly. If there is no vent, a number of problems may occur: The fixture without a vent may drain slowly. The drain will likely make gurgling noises.
Does each toilet need its own vent?
“Does a toilet need a vent?” And the answer is yes, your toilet has to have a vent. For more information on the great importance of plumbing vents, read our plumbing vent article here. And the size of this vent pipe depends on your local plumbing code.
Does every plumbing fixture need its own vent?
No bathroom plumbing system is complete without ventilation. When you flush the commode or drain the tub, wastewater pushes the existing air in the pipes and can form a water lock if additional air does alleviate the vacuum effect.
Does each plumbing fixture need its own vent?
Section 904.1 requires the vent system serving each building drain to have at least one vent pipe that extends to the outdoors. The most widely used method is commonly referred to as a conventional venting system. Table 909.1 (below) provides the maximum distance allowed for a vent in relation to the trap.
How do you vent a washing machine drain pipe?
Quote from the video:
Quote from Youtube video: And I think most code is is a two inch you will notice that I put this all right at the bottom is about 42 inches off the ground.
What is code for washing machine drain?
According to the Universal Plumbing Code, the standard for washing machine drain size is 2 inches. The P-trap should be between 6 and 18 inches high from the floor, while the pipe should be between 18 and 30 inches high from the floor. These standpipes connect to the home sewage system and should also be vented.
Can a washer and toilet share the same drain?
Some buildings have multiple waste lines that are connected to different appliances. However, if you’ve already taken note of the fact that your toilet gurgles whenever the washer drains, they’re definitely using the same system. That means that they also share the same vent stack.
Can 2 toilets share the same vent?
Most houses have more than one toilet, and if they are on the same side of the house, their waste lines can usually tie into the same stack. If they are on opposite sides, however, each may need its own stack. Since the stacks must be vented, this would mean two vent openings on the roof.
What happens if you don’t vent a toilet?
Poorly-vented drain lines will not be able to effectively move wastewater and solid waste out of your building. This could lead to problems such as overflowing drains, backed-up toilets, and similar plumbing issues.
Can a toilet and sink share a vent?
Wet venting is most common in conjunction with toilets and sinks; the drain for the sink is also the vent for the toilet. It can also be used for a variety of other applications but due to the following rules this is the most convenient and common situation to run into.
How many sewer vents do I need?
At least one main vent stack is required for every building that has plumbing when connecting separately to the sewer for the building or its septic tank. The stack has to run the most direct route through open air or be ventilated to extend to open air.
Do plumbing vents have to go through the roof?
It does not have to go through the roof. From the plumbing code (I have the 2003 edition), P3103: It must not be less than 4 feet directly beneath a door, openable window or other air intake of the building or adjacent building.
How far away can a vent be from a toilet?
6 feet
According to the UPC, the distance between your trap and the vent should be no more than 6 feet. In other words, for the vent to work properly, it needs to feed into the drain line within 6 feet of the trapways that connect to it.
Where should a toilet vent be placed?
Quote from the video:
Quote from Youtube video: Right under the center of our plumbing wall the discharge side connects to the building drain further downstream.
What size vent pipe is required for a toilet?
Toilet vent pipes are usually configured by feeding a 2-inch PVC pipe within the wall in back of the toilet down from the ceiling. This pipe connects right into the toilet drain pipe. Then, the tub/shower drain pipe and sink drain pipe are vented with 1.5-inch pipe, and these branch off the toilet pipe.
Can a plumbing vent be upstream or downstream?
So can a toilet vent be upstream? A toilet vent can be upstream. The purpose of the vent pipe is to allow the sewer’s gases to escape from the house’s roof rather than inside the house. A vent also allows oxygen to enter into the sewer pipes, which allows the waste to break down and prevents clogging.
Can a toilet be vented downstream?
Can a toilet vent be downstream? Never. A toilet vent always should be upstream. The purpose of the pipe is to allow sewer gases and water from entering your house.
