Just plaster over it. Cables in walls would ideally have capping placed over them, or cables in plastic conduit but that’s more to do with protecting the cables from the spread’s tools. If these are cables clipped to the underside of joints then just plaster over them.
Is it OK to plaster over cables?
Yes the regulations do allow for cables to be just plastered over, although a good electrician would have installed Oval conduit or capping, so it sounds like he has done just the basics to keep the costs down and save a few pounds.
How do you plaster around cables?
Quote from the video:
Quote from Youtube video: Just some stuff a lot from wigs ages ago it's last a long time so I've actually mixed it up to the consistency of milk. So that's four or five parts water to one part PVA.
Do cables need to be capped?
I don’t know about good practice but there is no requirement to cap the cables. I would on an open wall but not in a chase generally. They aren’t going to get damaged in a chase by a trowel are they.
See Also:
| Technical discussion forums | |
|---|---|
| ยท | Other and general engineering discussions |
| Archived categories |
How do you cover exposed wires on a wall?
How to Hide Wires in a Wall
- Use a stud finder to find a spot between two studs in the wall. Mark the wall where you want the upper and lower holes to go. …
- Attach a drywall hole saw bit to a power drill. …
- Insert the cord or cords through one of the hole covers. …
- Insert the hole covers and push firmly into place.
Do you need to protect cables in walls?
All electrical cables should be set into the walls at a minimum depth of 50mm if they are not mechanically protected. If it isn’t possible to chase the walls to that depth then the cables should be set deep enough so that metal capping can cover them and allow for plaster to cover that.
Can you put filler over electrical wires?
As others have said, its a bodge, and potentially dangerous. Over time the filler will corrode the copper making the join unsafe. The best remedy would be to pull in (or chase in) a new cable to a point where it can be safely joined as joins cemented into the walls are far from ideal.
Do you plaster before electrics?
You’ll want your electrician first. He/she can make holes in your existing ceiling to run cables and find joist without the worry of damaging your new ceiling as you’ll be re-boarding and plastering once the electrician has first fixed. Then your plasterer can board and skim your existing ceiling.
Can you bury electrical wire in wall?
Terminated, capped electrical wires should never be buried behind drywall, whether loose or in an electrical box. The leading edge of the electrical box must be flush with the drywall.
Can I bury a live wire in a wall?
You can simply use tape over the live wire to fit into the cap. However, it is important to terminate the wire in a junction box and avoid burying the wire in the wall. The tape may come off when temperatures change and in such situations, live electrical wires potentially become dangerous.
Can exposed wires cause a fire?
As many of us know, exposed wire creates a fire hazard. An aging system with worn-out insulation that leaves wires exposed is vulnerable to power surges, overheating, shorting out and encountering other elements in the wall that can cause a fire.
How do you hide unsightly wires?
7 Easy Ways To Hide Cords And Cables
- Make A Simple Fabric Panel. If you’re tired of seeing a mess of cords hanging behind a piece of furniture with metal legs, you’re in luck! …
- Bundle Cords With Zip Ties. …
- Run Them Under Rugs. …
- Keep Cord Hubs Out Of Sight. …
- Use Adhesive Hooks And Clips. …
- Get A Cord Wrap. …
- Set Up A Charging Station.
How do you seal electrical wires?
Quote from the video:
Quote from Youtube video: Simply. Use a razor to cut off a length of tape that you'll need when wrapping the connection applied two-thirds. Overlap. This tape will fuse on both sides. And once cured it will remain flexible.
Can I bury electric cable in plaster?
1: If cables are to be buried in plaster, then PVC capping is sufficient to give basic mechanical protection from pasterers tools, however it’s primary purpose is to prevent chemical leaching of cable molecules into the plaster, which can produce acidic or alkanine products when the tweo come into contact.
How do you run wire in plaster walls?
Quote from the video:
Quote from Youtube video: He runs from the top of the wall. And actually busts a channel between those two layers of plaster until he gets to the next floor where he can run his wire.
How deep are electrical wires in walls?
How far into the wall are wires located? Wiring usually runs horizontally, about an inch into the wall. The parameters are 6 inches or 12 inches above the receptacle.
How do you check if there are wires in a wall?
According to Popular Mechanics, the best tool for locating wires is a stud finder with AC wire detection. Use painters’ tape around the area you wish to scan; this will serve as a place to mark the location of the wires after detection.
Is metal capping required?
There is no requirement to earth metal capping buried in the wall as it is not an exposed conductive part or an extraneous conductive part.
How do you run cables behind plasterboard?
Quote from the video:
Quote from Youtube video: Directly below the box feed your fish tape into the wall opening. Pushing it up into the hole you made in the topically. If you're running cable through a basement or crawlspace. Push.
Can you hide TV power cord behind wall?
4. Run TV Wires Behind the Wall. The best solution for keeping the cords of a wall-mounted TV out of sight involves hiding them behind the wall itself using recessed cable plates like this top-rated Easy Mount Cable Organizer Kit available at Amazon.
