If there is no indication whatsoever then no, it doesn’t matter. That looks like an internationally universal ballast, so in the US you’d have two hots @ 240V/60Hz, and in a place like the UK you’d have a hot and a neutral @ 230V/50Hz.
Does it matter which way live and neutral?
The answer is fairly clear. Yes it matters, because it reduces the possibility of an appliance/device becoming a shock hazard.
What happens if a ballast is wired wrong?
The ballast is wired to the home’s hot, neutral and ground wires on one end, and to the light fixture’s lamp holders on the other end. If a ballast fails, it can cause a short, burn out tubes or even cause a fire, so it must be replaced.
What happens if live and neutral are reversed?
If your outlet’s polarity is reversed, it means that the neutral wire is connected to where the hot wire is supposed to be. This may not sound like a terrible thing, but it is. There is always electricity flowing out of an outlet with reversed polarity, even if an appliance is supposed to be off. Why is it dangerous?
How do you wire an electronic ballast?
Quote from Youtube video: Now depending on what you're switching to or what you're taking out there may be different wiring so in this ballast. This old ballast here we've got a black and a white and a blue and a red here.
How do you ground a ballast?
If the ballast doesn’t have a ground wire or terminal the ballast is just grounded to the fixture housing by it’s mounting screws. The ground wire on the cord usually attaches to a designated (green) screw on the fixture frame.
Can you splice ballast wires?
In the case of installing an electrical fixture, a splice is used to connect the lead wires of your fixture (it doesn’t matter whether it’s a ceiling fan, ballast, or downlight housing, they all have cable leads) to your house’s line voltage.
How do you hook up an electronic ballast to a fluorescent light?
Quote from the video:
Quote from Youtube video: For two parallel fluorescent tubes. We will duplicate the ballast. And the shorter connect the line source to one pin of the switch. The other pen will be connected to one pin of each ballast.
Does ballast have polarity?
If the lamp is fluroescent, it has a ballast. If you can get to that, the ballast should be marked with either the polarity or the usual black and white wires for hot and neutral. Polarity should not matter though, with AC power.
What do I do with the yellow wires on a ballast?
The common yellow wires connect from the ballast to push-in connectors on one of the right holders of lamp 1 or 2. Two yellow wires connect the common lampholders together.
What do the yellow wires on a ballast do?
The common yellow wires connect from the ballast to push-in connectors on one of the right holders of lamp 1 or 2. Two yellow wires connect the common lampholders together.
How do you know if a ballast is bad?
If your fluorescent lighting is displaying any of the signs below, it could be a symptom of a bad ballast:
- Flickering. …
- Buzzing. …
- Delayed start. …
- Low output. …
- Inconsistent lighting levels. …
- Switch to an electronic ballast, keep lamp. …
- Switch to an electronic ballast, switch to a T8 fluorescent.
How do you change the ballast in a fluorescent light?
Instructions
- Remove the Cover. Remove the lens, or diffuser cover, from the fixture. …
- Remove the Fluorescent Tubes. Remove the light bulbs (fluorescent tubes). …
- Remove the Cover Plate. …
- Disconnect the Ballast Wires. …
- Remove the Ballast. …
- Prepare the Wires. …
- Mount the New Ballast. …
- Dispose of the Old Ballast.
How do you change a ballast without turning off power?
Remove the wire nut from one of the power wires and carefully strip about 1/2 inch of insulation from the end, making sure not to touch the end. Hold the ballast wire next to this wire with the stripped ends parallel but not touching. Quickly slip on the wire nut and screw onto the ends.
How do I stop my fluorescent lights from flickering?
Brush dust out of sockets, then reseat firmly. If the tube still blinks when the light is turned on, wiggle it a few times while the light is on to see if this cures the problem. If not, take the tube out and inspect sockets closely to see if spring contacts are bent or corroded.
Why does my fluorescent light have swirling lines?
The swirling or striation effect doesn’t necessarily mean something is majorly wrong with your lights. Theories suggest that reduced mercury vapor pressure caused by cold environments or impurities in the tube produce this strange phenomenon.
Why does my fluorescent light take a long time to come on?
Over time, the starter can wear down and ultimately take longer to do its job. Lights that take a long time to come on or flicker on and off without starting are common symptoms. If you suspect the starter may be the culprit, first check to make sure your light actually has one.
Why do my fluorescent lights burn out so fast?
There are many possible reasons why a light bulb burns out quickly: The power supply voltage may be too high. Bulbs may be loose or connected improperly. Excessive vibrations may be causing the filament to break.
Will a bad ballast burn out bulbs?
Causes of Ballast Failure
When it’s too hot or too cold, the ballast can burn or fail to start your lamps at all.
Is there a light bulb that lasts forever?
The Centennial Light is the world’s longest-lasting light bulb, burning since 1901, and almost never turned off, it is at 4550 East Avenue, Livermore, California, and maintained by the Livermore-Pleasanton Fire Department.
