How do you finish the edges of a rubber roof?
Quote from the video:
Quote from Youtube video: He's then going to flap the sheet over onto the roof deck. Until expose the area that we need to bomb down secure it with the yellow bonding. Adhesive.
How do you put trim on a rubber roof?
Quote from the video:
Quote from Youtube video: Trim off the excess membrane from the gutter edge if stapling. The membrane of the corners. Ensure the staples are always weathered prior to installing the Shore edge check curb.
How do you finish EPDM?
Quote from the video:
Quote from Youtube video: And work your way down and then it will shape and mold into place when it reaches the roof deck. Finish off with the silicone roller and the penny.
How do you corner EPDM?
Quote from the video:
Quote from Youtube video: Position the tape ensuring it extends 75 millimetres onto the deck area and fifty millimeters beyond the membrane at the highest.
How do you fit fascia boards to a flat roof?
Quote from the video:
Quote from Youtube video: So that's what you need to do is cut that little section. Out just there so that slides. In we've put on the soffits. And fascias we've used the black polytop pins.
Do you need drip edge on flat roof?
Drip edge is not necessary in most flat roof installations. During ice storms, drip edge protects roof line during ice dams that can occur during the winter months. At the bottom of the roof, the edge helps gutters direct water away from your house and foundation.
Can you walk on EPDM rubber roofing?
Full Answer. All of our roofing systems are designed to take foot traffic and will withstand access to the roof for window cleaning and general maintenance The EPDM systems can be walked on both during and after installation, EPDM is designed to take LIGHT foot traffic for occasional cleaning or maintenance.
What is fascia trim?
Fascia is a specific type of trim, which is installed just below the roof line. It helps to cover the soffit, and provides a more finished appearance for the roof and eaves of the home. These boards may vary in width, but is generally a slightly wider or thicker version of the same trim used on the rest of the home.
How do you flash a curb on a rubber roof?
Quote from the video:
Quote from Youtube video: Then apply bonding adhesive to the exposed membrane and four inches up the side of the curb. And allow it to flash. Off.
How do you flash a roof corner?
Quote from the video:
Quote from Youtube video: All you have to do is make one small cut along the top of the brick ledge there at the corner and fold. Around same thing back from the other side after some mastic is applied.
How do you fold a rubber roof corner?
Quote from the video:
Quote from Youtube video: The fold of the membrane vertically 75 millimeters from the corner. Remove the excess membrane from the fold. Mark the area to be taped 75 millimeters beyond this cut.
Is fascia board necessary?
The Best Fascia Tips You Will Read This Year. The short answer to this question is, “Yes!” They are undoubtedly necessary because they help cap the edges of the rafters, hold gutters in place to help ensure proper water drainage, and more.
How do you trim trimming fascia?
Quote from the video:
Quote from Youtube video: Using metal cutting snips trim the top section at your mark. At the bottom of the trim mark the distance of trim. Needed then cut along the line.
Does soffit go on before fascia?
The job goes smoother when you follow the correct installation sequence. First nail up the J-channel, then soffit panels, then fascia, then drip edge.
What is the difference between a soffit and a fascia?
An exterior soffit is located on the span beneath the rafter tails, while the fascia is the exposed horizontal band you see at the end of the rafters. These architectural elements found along the eave area do more than just add visual interest and give a finished look to your home.
Can you install soffit without fascia?
Yes. You can install a soffit without installing a fascia. By using J channels instead of a fascia board, a soffit can be installed under the roof without a fascia.
How do you finish soffit and fascia?
Quote from the video:
Quote from Youtube video: We're going to take a trim nail. And instead of nailing the face of it this time we're going to nail. It. Up under into the groove of the soffit. So we'll go ahead and get a nail started here.
How do you install soffit trim?
Install each panel one at a time:
- Insert the soffit panel into the channel.
- Make sure the panel forms a 90-degree angle with the wall.
- Nail up the panel.
- Repeat these steps for each panel.
- Be sure the tongues and grooves of each panel line up with the panels alongside them.
How do you overlap fascia trim?
Quote from the video:
Quote from Youtube video: You want to start from the bottom and work your way up. So that each piece overlaps and when water runs it runs over the next piece on its way down. And you probably want to nail it every 36. Inches.
