How do I fix the igniter on my gas fireplace?
Quote from the video:
Quote from Youtube video: Bottom taking a look inside you can see the parts where the spark is supposed to emanate from and right here we have a thermocouple. And that just measures the temperature. Right.
How do I light the pilot on my gas fireplace without ignitor?
Quote from the video:
Quote from Youtube video: This button right here it's on P for pilot. So I'm gonna hold it down you'll hear the gas. Okay so you're supposed to hold it down for a little while. And then turn it to the on. Position.
How do you start a gas fireplace with a key to the wall?
Igniting with a Fireplace Key
- Look over the user manual included with your fireplace. …
- Remove your fireplace’s outer cover. …
- Put a fireplace key into the device’s gas valve knob. …
- Hold a long lighter up to the burner and ignite it. …
- Turn the gas key. …
- Replace the fireplace’s outer cover immediately.
How do you start a pilot light on a gas fireplace?
Quote from the video:
Quote from Youtube video: If you look up in here I can hit the seal a little spark. There we go three clicks. Now I hold down I continue to hold down. This for about a minute now.
What would cause a gas fireplace not to ignite?
Check the Spark Igniter
If gas is coming out of the pilot but it still won’t light, the spark igniter could be the problem. You should clear out any debris between the igniter and thermocouple. Blowing compressed air into the pilot area, waiting a couple minutes, then trying again could help to fix the problem.
What causes a gas fireplace not to ignite?
Another common issue with ignition is a dirty pilot light orifice, caused by a buildup of soot and dirt. If you have successfully re-lit your pilot light, ensured that the orifice is clean, and the fireplace still refuses to ignite, there could be an issue with the thermopile, thermocouple or wiring.
Can you manually light a gas fireplace with electronic ignition?
Re-lighting pilot lights is straightforward on today’s modern gas fireplaces. If you have an electronic ignition unit, using your remote control simply press the ‘on’ button and the pilot will re-ignite within a few seconds, followed by the fireplace a few seconds after that.
How much does an igniter for a gas fireplace cost?
Gas Fireplace Igniter Replacement Cost
The price of igniter replacements ranges from $100 to $200. If a igniter stops working, the gas unit essentially becomes useless, so this is something most people must replace urgently.
How do you clean a thermocouple on a gas fireplace?
How to Clean a Thermocouple on a Gas Fireplace [3 Steps]
- Step 1: Leave the gas to cool first if it has been burning.
- Step 2: Polish the thermocouple.
- Step 3: Blow it out.
- Step 4: Light the gas.
How do you start a gas fireplace manually?
Turn the knob from the “Off” to the “Pilot” position. Push in the pilot knob, which manually sends gas into the system. Push the igniter button once every second until it lights. Depending on how long it’s been since the gas fireplace was last used, ignition may take multiple attempts.
What happens if pilot light goes out on gas fireplace?
A pilot light may need to be re-lit from time to time after being extinguished on purpose or by accident. If it is accidentally extinguished, there exists a danger that the gas used to keep the flame lit will continue to vent, possibly into the living space.
Is there a fuse in a gas fireplace?
Gas fireplaces have a fuse for the electronic ignition system, and a power surge may have tripped the circuit breaker preventing your gas fireplace from igniting. If the circuit breaker is off, flip it to the on position.
What do I do if my pilot light won’t light?
If your pilot light won’t stay alight, it might be the thermocouple. Sometimes dust buildup collects on the thermocouple and blocks the sensor. Try cleaning the thermocouple and then relighting the pilot light. If it continues to go out, the thermocouple might need to be replaced.
Where is thermocouple on gas fireplace?
Find the thermocouple, which is located next to the pilot light and looks like a small straight pipe.
How do I know if my thermocouple is broken?
After about a minute, when you’re sure the probe has gotten hot, place one lead on the shaft of the thermocouple and the other lead on the connector. If the reading is less than 25 millivolts, the thermocouple is bad and needs to be replaced.
How do I know if my thermocouple is bad on my gas fireplace?
Quote from the video:
Quote from Youtube video: You should replace the thermocouple. So to recap the readings to look for are 8 to 30 millivolts. And if the readings are less than 7million. You should replace the thermocouple.
What does thermocouple look like?
The thermocouple is made up of a tube, a bracket, and wires. The tube sits above the bracket, a nut holds the bracket and wires in place, and underneath the bracket, you will see the copper lead wires that connect to the gas valve on the furnace.
Can I replace a thermocouple myself?
It’s easy to replace and a new one costs $5 to $10. Rather than trying to unfasten the thermocouple inside the water heater’s burning chamber, it’s easier to remove the whole burner and thermocouple assembly.
Can you clean a thermocouple?
Yes, you can clean a thermocouple, but the task must be done with a light touch. Remove the thermocouple from the process assembly, using a steel wool or emery cloth, lightly clean the tip removing any build up. Cleaning a thermocouple is not a fix for an issue, such as inaccurate readings.
