Step 2: Turn off the power switch if your gas fireplace won’t turn off. Beginning at the fireplace, check the switch to make sure the unit is on. The controller may be on the side of the fireplace or behind a panel in its front. If there is no switch, it could be on the wall near your fireplace or elsewhere in the room …
How do you turn off a gas fireplace with a wall?
To turn off the gas fireplace, replace the wall key. Turn the wall key clockwise until it comes to a firm stop. The flame will taper down and extinguish on its own.
How do you use a gas fireplace with a wall switch?
It’s easy to know how to turn on a gas fireplace with an electronic ignition wall switch. Many gas fireplaces come equipped with a wall switch control panel for activating the unit and adjusting the level of the flame. Simply push the “On” button and the pilot should ignite.
How do you test a fireplace wall switch?
- Open the control panel of your gas valve.
- Locate two terminals called ‘TH’ and ‘TP’.
- Take a jumper wire, paperclip, or a small insulated wire. Put the bare ends of it to the terminals from the previous step.
- Try turning on the fireplace as usual. If it works, then a bad wire is confirmed.
- Step 1: Review Owner’s Manual. Read through the included manual thoroughly before starting up the gas fireplace. …
- Step 2: Remove Front Panel. …
- Step 3: Insert Key into Gas Valve. …
- Step 4: Light The Burner And Turn Key Counterclockwise. …
- Step 4: Replace Front Cover.
Why is my fireplace switch not working?
What can happen over the years, is that the connections inside the switch can get dirty, corroded, or broken, causing a loss of this voltage at the switch. So by the time the small amount of voltage gets sent back to the fireplace, it is not enough to signal the fireplace to turn on.
Where is the gas shut-off valve for gas fireplace?
Gas fireplace: The shut-off for a gas fireplace is typically on the control panel. This control panel can be found behind the front screen, where a knob that controls the flow of gas can be turned to ‘off’.
Do gas fireplaces turn off automatically?
Nearly every new gas fireplace comes equipped with safety features such as a 100% fail-safe shut-off valve. If the pilot flame goes out, the gas flow will automatically turn off. Another safety device is a safety pilot.
Do you need a special switch for a gas fireplace?
The Robertshaw gas valves very widely used in gas fireplaces are rated for 100 milivolts of coltage loss through the main burner control circuit —a typical wall switch has 10-15 millivolts of loss. So in my experience, there is no particular need to use specialized switches.
Is it OK to leave the pilot light on in a gas fireplace?
Generally speaking, it is safe to leave your continuous pilot light on at all times, assuming it stays lit (more on this in a moment). While it does cost more to keep your pilot light on in between uses, it can actually have some benefits to your system.
How does a fireplace wall switch work?
When you flip a wall switch, click your remote control or the thermostat starts calling for heat, the gas valve on your fireplace will open. Gas valves generate their own electricity and operate on millivolts, a very small amount of electricity.
Why does my gas fireplace not stay on?
If the pilot light on your gas fireplace won’t stay lit, a very likely culprit is a component called a thermocouple. A thermocouple is a safety device and is a component of the ignition system. Its purpose is to not allow the gas valve to open if the pilot light isn’t lit.
What is the switch on the side of my fireplace?
If the damper is not fully open, smoke and carbon monoxide from the fire will vent into your home. To open the damper, locate the lever at the top of the inside of your fireplace. Depending on your fireplace model, the lever will either shift from side to side or up and down to open your damper.
How do you manually turn on a gas fireplace?
Light A Gas Fireplace With A Gas Valve Fireplace Key
How do you turn off a gas fireplace valve?
Quote from the video:
Quote from Youtube video: It turn up to the pilot. Position you press it in a little bit and you can go ahead and turn that to the off position that shuts the gas off to the entire fireplace.
Should I turn off the pilot light on my gas fireplace in the summer?
Your Utility Bill
Perhaps the most important reason to turn off gas fireplace pilot light in summer is because of the money and energy you will be saving. If you leave the pilot light on during the summer it is simply sitting there burning gas, which is wasting gas and contributing to an exorbitant energy bill.
How do I turn off the pilot light in my gas fireplace?
Turning off your pilot light is a simple process that will save you both energy and money. All you have to do is open the front of your fireplace, turn the Pilot knob to “off,” and then turn your gas shutoff valve to the “off” position as well.
How much does it cost to keep the pilot light on a gas fireplace?
A pilot light is a small flame that is kept lit to provide a catalyst for the main burner to be turned on when needed. The average fuel consumption of your standing Pilot light is: Natural gas is $0.60 a day = $219 a year. Liquid Propane is $1.80 a day = $657 a year.
How do you turn off the pilot light on a gas fireplace?
On some fireplaces, there will be a “Lo-Hi” button that allows you to adjust the flame upward or downward. On others, there will be a screw that you can easily adjust with a screwdriver. Turning the screw clockwise will lower the flame, while a counterclockwise motion will turn it up.
How do you turn a pilot light off?
Quote from the video:
Quote from Youtube video: The pilot flame will become higher. When we turn the screwdriver to the right clockwise. The pilot flame will become lower.
Why does my pilot light make noise?
If there is a roaring sound that occurs when the pilot light is on, it is usually because the flame needs to be adjusted. A grinding or shrieking noise is usually caused by a fan or blower.
