A solution to your problem is to put a restriction in your washing machine discharge hose to slow down its flow to what your drain can handle.
…
- The “classic” version of this is the “Laundry sink” – which you can still get, fairly inexpensively for plastic versions. …
- @Ecnerwal.
How can I make my washing machine drain better?
5 Easy Steps to Get Water Out of Your Washer
- Step 1: Power It Down and Turn Off the Water Supply. Start by powering down your machine. …
- Step 2: See If You Can Drain the Drain Hose. …
- Step 3: Check Out the Drain Pump. …
- Step 4: Drain the Interior Manually If Needed. …
- Step 5: Know When to Call a Professional.
How many gpm does a washing machine discharge?
Washing machine pumps are now discharging drain water much faster than older machines. The current rate is 17-22 gpm where the older rate was around 12 gpm. The benefit for the home owner is a faster wash time, more water circulations in the wash cycle – leading to cleaner clothes in less time.
Why does my washer drain so fast?
It’s because the water flows out faster than the pipe can drain. The easiest way to fix this is to seal up the washing machine waste hose against the open PVC pipe. Some gaffer tape should do the trick.
How high can drain hose be for washing machine?
In order for the drain hose on your Top Load washer to function properly, the drain must be at least 30″ up from the floor and less than 8 feet high.
Does washing machine drain into sewer line?
Washing machine drains are fed by an electric pump, which moves water from inside the cleaning drum, through a flexible drain hose on the underside of the machine, and out into your home sewer system where it makes its way out of the house.
Why does my sink gurgle when washing machine drains?
The gurgling sound from your kitchen sink results from the vent being blocked. So when the washing machine water is draining, the air in the vent will be pushed by the water, and because the vent is already blocked, the air will escape via the sink and thus the gurgling sound.
Can a washing machine drain into 1 1 2 pipe?
Drain and Trap Requirements
A 2-inch drain pipe is required for all washing machines. The former requirement of 1 1/2-inch pipe is not enough to handle the fast drainage of modern washers.
What is the flow rate of a washing machine?
A toilet will normally use about 2-3 gallons per minute (gpm), a shower from 1.5 to 3.0 gpm, a bathroom or kitchen faucet from 2-3 gpm, a dishwasher from 2-4 gpm, and a washing machine from 3-5 gpm.
How do you vent a washing machine with an AAV?
To vent a clothes washer with an AAV, I run a 1 1/2-inch pipe up from a tee located about 4 inches behind the 2-inch trap, terminating it in the washer box. That’s where I install the AAV; one box does it all. However, remember that the horizontal pipe the trap dumps into must be at least 3 inches in diameter.
How do you route a washing machine drain hose?
Reach around to the back of the washer with the measuring tape or yard stick. Leave the machine in its current position. Measure the maximum height of the discharge hose, at the arch, from the floor where it terminates into the standpipe in the floor, nearby laundry sink or recessed drain in the wall.
How do you position a washing machine drain hose?
Typically the hose is hung from over the side, and then over the top rim of the sink. It is important to have a sizable air gap between the end of the drain hose, and the bottom of the sink. An air gap prevents backwater from ever getting sicked back into your washing machine.
How do I extend the drain hose on my washing machine?
- Unhook the existing drain hose from the standpipe, either by disengaging the hose from the curved hose form or pulling out the curved portion of the pipe. …
- Measure the distance to the new washer location and buy a drain hose extension that is long enough to reach.
Can I use a garden hose to drain my washing machine?
Yes! You can use your garden hose with your washing machine. For both internal and external water hookup systems. Using your garden hose for your washing machine is a simple and inexpensive way to get your machine up and running.
