How do you hook up an air compressor to a sprinkler system?
Quote from the video:
Quote from Youtube video: It's a three-quarter inch female threaded adapter. It's it's 3/4 inch to a 1/2 inch adapter. And then this piece here is threaded as well this half-inch side.
How do I make a sprinkler blowout adapter?
Quote from the video:
Quote from Youtube video: This is my blowout valve. And as you can see it's a regular male threaded hose connector. And I'm this piece that I kind of pieced together from Lowe's or Home Depot.
What compressor is good for sprinkler blowout?
Makita small air compressors are best for blowing out a sprinkler system and removing water from surfaces. They provide a quick recovery time and are easy to maintain by all means. The low noise level is an important consideration when choosing one.
Where do you plug an air compressor into an irrigation system?
Sprinkler systems feature a fitting to allow the connection of an air compressor.
- Locate the control panel for the sprinkler system. …
- Close the airflow valve on the compressor. …
- Go back to the control panel and manually open the sprinkler zone that is the farthest from the panel or at the highest point on the system.
Can I blowout my sprinklers myself?
Sprinkler systems need to have all the water blown out of them before the winter freeze. If you have an air compressor you can do the job yourself and save the service fee.
How do you blowout your sprinklers?
Blow-Out Method Procedure
- Shut down the water supply and connect the air compressor to the irrigation system using the coupler. …
- Find the sprinkler station highest and farther from the compressor and turn it on.
- Close the backflow valves.
- Slowly open the valve on the compressor.
- Gradually add more air pressure.
How do I bleed the air out of my sprinkler system?
Quote from the video:
Quote from Youtube video: Look for the screws holding them in place and unscrew them with a screwdriver. The air should flush out of the system within a few minutes. Turn on the irrigation. System at the control panel.
How do I stop my sprinkler system from water hammering?
If only one of the irrigation valves is causing water hammer the easiest solution is to reduce the amount of water that valve is using. That will reduce the velocity and the water hammer will stop. To do that you need to reduce the number of sprinkler heads the valve operates.
What does the bleed screw do on a sprinkler valve?
Quote from the video:
Quote from Youtube video: You can use the bleed screw to flush debris stuck in the valve allowing the valve to close all the way.
Why is my sprinkler system so loud?
Improper Water Pressure
High water pressure entering your irrigation system may produce loud sounds called water hammer, reveals Irrigation Tutorials. Because of their echoing effect, the noise may seem like it is emanating from a particular sprinkler.
Why do my pipes rattle when sprinklers turn on?
Like indoor plumbing, air trapped in the system can cause a hammering sound along the pipes and especially near the sprinkler valve. This knocking sound is called water hammer and is cured by passing the air through the piping system.
What causes air in sprinkler lines?
In most irrigation systems, the pipelines are full of air when the system is not in use. When your irrigation system shuts down most of the water drains out through the emitters or any auto drain valves you might have installed and is replaced by air. Additionally, pumps can introduce air into the system.
Can a bad sprinkler valve cause water hammer?
It might be a good idea to replace the valve. Splitting valve zones is another good way to rid water hammer. If only one of the irrigation valves is causing water hammer, the easiest solution is to reduce the amount of water that valve is using.
Where should hammer arrestors be installed?
The best places are either close to the pump, isolation or check valve that is originating the hammer, or at more distant points where the pipe changes direction, for example at the top of a pump riser.
How do you install a water hammer arrestor?
Quote from the video:
Quote from Youtube video: And reconnect the supply line to the water hammer arrestor. Hand tighten and then use a wrench to a quarter turn be careful not to over-tighten. Turn. The stop valve to the open position followed.
