What can I do with old lath and plaster walls?
Updating lath and plaster walls to drywall can be done by covering or replacing them altogether. You can cover the old plaster by installing drywall panels on top. This is the simplest and least messy way to go, but not necessarily the most efficient.
Can you retrofit a shower niche?
A retrofit niche is a product that is installed in the process of a new shower remodel project after the shower wall tile has already been installed and grouted. During a complete shower wall reconstruction, the retrofit niche hole is cut out of the the tile backer board after it’s attached to the shower wall framing.
How thick does a wall need to be for a shower niche?
The typical depth of a shower niche is 3.5 inches, the width of a wood stud. In a high rise building, the steel studs may be 2.5 inches deep and this should be considered. This is still wide enough for most bottles. Niches should not be against outside walls if possible in cold weather climates.
How do you make a homemade shower niche?
Quote from the video:
Quote from Youtube video: You end up with a 16 inch height that we're gonna be working with ok. So first of all we want to walk mark on the wall we're gonna make it 16 inches and that is finish tile to finish tile.
How do you screw into lath and plaster?
Quote from the video:
Quote from Youtube video: You're going to want to find a drill bit that's the same size or just a hair bigger than your plastic anchor these plastic anchors are designed mainly for your concrete.
How do you find studs in a lath and plaster wall?
Quote from the video:
Quote from Youtube video: If there's anything metal they'll find it they're extremely difficult to separate. They really want to hang on. So what we're going to do is putting it on the wall until it finds a nail underneath.
Can you install a shower niche to an existing wall?
The short answer, NO it cannot be added later. The moment you touch that tile you ruin the integrity of the waterproofing. There are tons of other solutions for holding products so look into those unless you’re ready to completely redo the shower.
What can I use instead of a shower niche?
Well the good news is, there is an alternative, and we are loving it! Introducing the tiled shower ledge. Put simply, a tiled shower ledge is a half-height wall built into your shower, a modern and practical way to house your most-used bathroom products.
How do you install a premade shower niche?
Quote from the video:
Quote from Youtube video: And fit step number three secure the niche into place by applying true seal sealant or modified thinset mortar onto. The back and sides of the hole. Opening then pressing the niche firmly.
How do you build a recessed niche wall?
Quote from the video:
Quote from Youtube video: Now I'll put my two rolls on two lines in and I'll cut the plasterboard. Out. Now that I've made my cap I've checked that the nice does fit I'm ready to secure it in with some screws.
How do you build a bathroom wall niche?
[How-to] make a wall niche in your bathroom
- Determine location & Cut out cavity. Place the build-in set into the desired position. …
- Clean work area & apply sealant. …
- Apply self-adhesive waterproofing membrane. …
- Apply sealing compound. …
- Start tiling. …
- Insert wall niche.
What is the standard size of a shower niche?
Assuming that you are considering installing a prefab tile ready foam board shower niche, the most popular standard shower niche size is 12″ wide x 28″ high x 3-1/2″ deep.
Does a shower niche have to be centered?
I see no reason it needs to be centered. I would put it either on the same wall as the shower head, or on the back wall near the corner, to keep it out of the shower spray.
Do you have to tile a shower niche?
Everything that has a groove, recess or a niche in a bathroom must be waterproof. Adequate measures must be taken to ensure that there is no leakage from the niche sill into the rest of the wall. To ensure this, tiling a shower niche is not as simple as it may look like.
What is a shaving niche?
One option is a a creative use of a shower niche, which have commonly been used to store soaps, shampoos and other bath supplies. Adding a shaving niche on the lower part of your shower can also provide a space to easily prop up your leg when shaving.
How high should a shaving niche be?
As a rule of thumb, the best height to install a shower niche is 1200mm from the floor. This puts your shower products at just the right height to grab and use easily.
How high should a shower ledge be?
The ideal height of a shower niche is at chest to eye level when standing. However, that’s strictly related to the height of each individual person. On average that usually means a height of 48 to 60 inches (120-150 cm).
What height should a shower valve be?
30-50 inches
The average height for a shower valve is 30-50 inches above the floor, though this is a general range. For tub-shower units, the height can be just a few inches about the tub or directly on the tub as part of the faucet.
How far should shower valve sticks out from wall?
A shower valve should not stick out too much from the wall. It’s recommended for the base of a shower valve to sit flush against the wall. In general, a shower valve can stick out 3-4 inches from the wall. If it sticks out too much, this can look odd and take away from the shower’s aesthetic.
How far can shower head be from valve?
How Far Can Shower Head Be From Valve? A showerhead can be 2-3 feet away from a valve as long as it’s integrated into the plumbing. The water needs a controlled path to travel without the potential of a blockage.
