How do you remove ABS P-trap?
Quote from the video:
Quote from Youtube video: Place your bucket directly underneath the p-trap. Start with the lock nuts you'll get a little bit of water out remove your first slip joint nut remove your second lock nut.
How do you replace a ABS P-trap glue?
Cut two sections of PVC pipe (5 inches or longer) that are the same diameter as the existing pipe. Remove burrs. Apply PVC primer to one outside end of both pipes and the inside ends of a new P-trap. Apply PVC cement to all primed areas and push the cemented pipe ends into the ends of the P-trap.
How do you remove a P-trap from the wall?
To remove the P-trap from the wall stub, hold the trap assembly firm with one hand and turn the coupling nut counterclockwise with respect to the wall stub until it comes loose. If the nut is overtightened or old, you might have to use a wrench or a pair of pliers for the purpose.
How do you remove P-trap cleanout plug?
Use an adjustable wrench or adjustable pliers to unscrew the clean-out plug from a P-trap. Place a bucket under the trap to catch the water that will spill out when you remove the plug. Turn the plug counterclockwise to remove it, install the replacement, and turn it clockwise to tighten it.
How do you disassemble a P-trap?
Unscrew the nuts holding a plastic P-trap by hand, gripping the trap firmly with one hand and rotating each nut counterclockwise. You must unscrew two nuts to remove the trap. One holds the trap to the tailpiece, the small length of pipe extending down from the sink, and the other holds the trap to the drain line.
How do you remove a drain trap?
Disassemble The Drain Trap
First, locate the drain trap. Then, unscrew the slip joint nuts found on each side of the “j” bend of the trap. Loosening these will remove the trap from the sink tailpiece and the neighboring wall fitting. If you have a newer sink, unscrewing the drain tap can be done by hand.
How do you remove a glued toilet flange from ABS?
Remove the Flange Sleeve Sections
To do so: Place the tip of this wood chisel at the point where the flange sleeve is glued to the drain pipe. Hammer the end of the chisel to pry the glued section of flange sleeve away from the drain pipe. Repeat for all sections of flange sleeve until it is completely removed.
How do you loosen glued PVC pipe fittings?
Quote from the video:
Quote from Youtube video: When you found the right one heat it thoroughly for around one minute and put it inside the pipe as such. What this does is it heats up the glue just enough for the pipe to unstick.
Can you Reglue ABS pipe?
If the leak is coming from a fitting, you may need to reglue or replace the fitting. If it’s coming from a length of pipe, you’ll need to cut out the damaged pipe and replace it.
How do you remove a trap under a sink?
Quote from the video:
Quote from Youtube video: Slide it off dump the water in. There. Loosen up these nuts now loosen. Them up all the way. And you can leave them right on the pipes. And then you can pull this down dump out a little water.
How do you remove a stuck drain plug?
Quote from the video:
Quote from Youtube video: Video i said put on a rubber glove. And just push. Down. As hard as you can with the rubber glove. So you got grip. Turn counterclockwise. And it pops up see.
How do you replace a P-trap in a bathroom sink?
Quote from the video:
Quote from Youtube video: You can replace it fairly easily. Here's what you'll need to begin remove the old drain assembly from the top down. Use your pliers to unscrew any stubborn slip nuts.
How do you unscrew a U-bend?
Grab a bucket or a large bowl and place it under the U-bend before carefully unscrewing the threaded caps on either end of the bent length of pipe. These should come undone easily unless the plumbing hasn’t been serviced in a while; if they’re sticking, add a little bit of lubricant to help them pull apart more easily.
How do you loosen a stuck metal trap?
Hold the P-trap pipe steady with a second pipe wrench. Turn the nut counterclockwise until it turns by hand. Pull the nut away from the house drain. Loosen and remove the nut holding the top of the P-trap to the bottom of the tailpipe, using both pipe wrenches.
How do you snake a curved pipe?
Quote from the video:
Quote from Youtube video: Through the blockage. The way you do that is you turn the handle as you push. Forward. Now you want to hold on to the end want to loosen the nut. Pull it out just a little bit tighten.
How do you make a homemade drain snake?
Homemade drain snake
- Start with an empty 2-liter plastic bottle.
- Cut the bottle around the circumference of the bottle to create a long, thin strip of plastic (it will look like a spiral as you’re cutting)
- At one end, cut a few small ridges or teeth.
Why won’t my snake go down the drain?
Too much force – When you’re trying to dislodge a blockage, it can be tempting to try and force a snake cable through the drain too fast. If you force it, sometimes the cable can bend back on itself or kink. Instead of forcing the cable, extend the snake cable a few inches at a time until you reach the clog.
