The best way to protect your hands is to be very deliberate about every movement you make around the saw, and keep your hands away from the blade by using a push stick or push block.
Can a bandsaw cut your finger off?
it cuts pinky fingers really well. all the way through the bone only skin holding it on.
Where should your fingers be when using a band saw?
Always keep your hands on the sides of the blade while operating…. never in front of blade!
How far away should your hands be from the band saw?
Do not place your fingers close to the saw blade when cutting stock. Always maintain a 4” margin of safety. If it is necessary to back the saw out of a long cut, turn the power off and wait for the blade to stop.
What 5 things should you avoid when using a band saw?
Never push on back of piece with fingers or thumb. Don’t reach across the blade. Make all cuts under power, not while blade is coasting. Never remove guard unless authorized by Technician or WRL Manager.
What are the guards on the band saw used for?
Guards. Bandsaws must be guarded. Guarding must prevent access to the bandsaw blade but still allow the employee to see the material being cut. If practicable, employees should use a push stick to guide the work piece through the cutting process.
When using a band saw the operator should avoid?
Do not use excessive force when pushing the wood past the blade. Do not back the stock away from the blade while the saw is in motion if the work piece binds or pinches on the blade. Do not stop a band saw by thrusting stock against the cutting edge or the side of a blade immediately after the power has been shut off.
What are the dangers of using a band saw?
Recognized Band Saw Hazards
- Emergency Situations (E-Stop) …
- Coasting & Freewheeling. …
- Unintentional Restarting. …
- Getting Caught-In or Caught-By Moving Parts (Nip Points) …
- Contact with Blade.
Should you wear gloves when using a bandsaw?
Do not wear gloves while using a bandsaw (or any powered saw, drill press, or planer for that matter). The gloves will give you a false sense of security and do very little to protect your hands. In fact, they may end up getting your fingers pulled into the blade if the material catches.
When you are finished using the band saw you should?
If it becomes necessary to back out of a long cut, you should: Turn off the motor. Bring the blade to a complete stop and then back the stock out carefully. Force the wood into the blade to get a good cut.
Why is it best to use a push stick when using a bandsaw?
Push sticks or push blocks should be used when operating standard woodworking machinery, including table saws, band saws, radial arm saws, jointer/planers and shapers. These sticks protect the hand while allowing good hand control of the stock as it is pushed through the cutting head or blade.
How far should your fingers be from the blade?
Select the correct machine speed for the type of scroll sawing task to be performed. Keep your fingers to the side of the saw blade. Never allow your fingers to be in front of the saw blade. Your fingers must be positioned more than two inches from the blade when the saw is operating.
What is the closest distance your hand should be to the blade?
Never allow the hands to come closer than 12 inches to the saw blade. Position the right hand so it is NOT in direct line with the saw blade. Remove the hand holding the stock down as it approaches the saw blade guard.
What two attachments must never be used together on the table saw?
Never Free-Hand a Cut When using a table saw, the woodworker should never attempt a free- hand cut. Instead, use the fence or miter gauge to guide the stock. However, keep in mind that the fence and miter gauge should never be used together, as the end grain of a piece of stock can bind against the fence.
What two things do we check before using the band saw?
Quote from the video:
You need to have setup before you can use the bandsaw for instance you have to have proper tension on the blade. And you also have to set these guide bearings.
What is the minimum distance your hands should ever come to a cutting tool while in operation is called the?
11. Maintain a margin of safety specified for the machine. This is the minimum distance your hands should ever come to the cutting tool while it is in operation.
When can you leave a machine that you are using?
When you have completed an operation on a machine, shut off the power. Wait until it stops before leaving the machine or setting up another cut. Never leave a machine running while unattended.
What should power hand tools be properly grounded through?
Ensure that the tools are properly grounded using a three-prong plug, are double-insulated (and are labelled as such), or are powered by a low-voltage isolation transformer: this will protect users from an electrical shock.
