Whether the bolt is rusted or just really tightly in place, try a series of methods to get the bolt off and get back to mowing.

  1. Place a block of wood between the blade and the Craftsman riding lawn mower’s deck. …
  2. Spray the bolt with a rust-penetrating spray. …
  3. Brush the bolt area with wire brush, loosening rust deposits.

How do you remove a stubborn mower nut?

Quote from the video:
Quote from Youtube video: Like I say I've got to come along to prevent it from shifting. And I'm going counterclockwise. So it should loosen hopefully whoa there we went.

How do you loosen a nut on a lawn mower?





Put a wrench socket of the correct size on the head of the bolt securing the blade to the blade holder, and apply force to the wrench handle in the counterclockwise direction to loosen the blade bolt. The bolt may have a 1/2-inch, 5/8-inch or 3/4-inch head, depending on mower model.

How do I remove the spindle nut from my mower deck?

Quote from the video:
Quote from Youtube video: That slide now flipped it over get you a 5/8 inch socket. And then be good if you've got a impact wrench to take it off take the blade off here.

Which way do you loosen a bolt on a lawn mower?

To remove the blade, you must turn the blade’s retaining bolt to the left, or counterclockwise. Before undoing the blade, tip the mower on its side with the engine air cleaner facing up and block the blade with a piece of wood so it can’t turn.

How do I remove a stuck bolt?

Quote from the video:
Quote from Youtube video: Use a 6-sided wrench or socket. If the bolt still won't break free consider using a tool extender to added torque just be careful not to break off the head of the bolt.

Are lawn mower blade bolts reverse thread?





Yes. The bolts that hold the mower blades on a Craftsman mower in place are reverse threaded. That means that to tighten the bolt you must turn it to the left (counterclockwise), and to loosen it you must turn it to the right (clockwise).

What size is the nut on a lawn mower blade?

What size are the tractor cutting blade retainer nuts and what direction should they be turned? The retainer nut on most of our riding mower blades are a 5/8″ thread diameter. This sized thread diameter nut normally requires a 15/16″ wrench or socket tool in order to remove/install.

How do you remove the bolt from a PTO clutch?

Quote from the video:
Quote from Youtube video: So it allows you to turn this bolt. And there you go see comes right off pull that off get your clutch off clutch usually comes off pretty easy once you unplug the wiring harness.

Do lawn mower blades turn clockwise or counterclockwise?

Since most lawnmower blades turn clockwise, the bolt often goes counter-clockwise. To check the mower’s bolt, you have to turn it off, remove the spark plugs, and lay the lawnmower on its side. The bolt sits in the middle of the blades.

Are Toro mower blade bolts reverse thread?



Yes and no. The lawnmower blades itself is not threaded, but most nuts that held the blade in place are reverse threaded. The reverse thread helps to secure the blade on the drive shaft such that the rotation of the blade does not loosen the nut.

Does wd40 loosen bolts?

If the bolt is stuck in place because of rust, you can use a bolt loosening spray such as WD-40 Penetrant Spray. This penetrating oil provides deep lubrication to loosen the nut or screw.

How do you heat a bolt for removal?

Quote from the video:
Quote from Youtube video: And just use a little bit of a fuel flame. To just kind of pre burn the area a little bit make sure there's no leftover penetrant or anything that might just flash into a flame.

Can Coke loosen a rusted bolt?



Bubbly soft drinks like Diet Coke and regular Coca-Cola contain phosphoric acid, a substance known to do a number on rust. Diet Coke doesn’t contain the sugars so it’s generally easier to clean up and doesn’t attract ants. Pour the Diet Coke or Evaporust around the bolt and let it soak in.

How do you loosen a rusted tight nut?

Quote from the video:
Quote from Youtube video: Step 4 when the bolt is cool enough to touch spray wd-40 on and around the nut and bolt. Step 5 tap the end of the bolt with a hammer to loosen the threads. And allow the oil to penetrate.

Will vinegar loosen rusted bolts?

Use Vinegar



All you need to do is to take them out, pour the vinegar in a cup and soak accordingly. Leave the bolts for a little more than a day. After the time has passed, take them out, scrub then with a brush and you should see the rust disintegrate.

How do you remove a rusted bolt without heat?

You can try the following:

  1. Use a lubricant to loosen the bolt and then remove it with a wrench.
  2. Use a clamp to cut the fastener’s head and help remove it from its position.
  3. Use an impact hammer or wrench to forcefully remove the bolt.



How do you remove a seized bolt without a head?

Quote from the video:
Quote from Youtube video: Once you get a good cut do you angle the chisel. And start working until you break the bolt loose. Like that and now you can do nothing until you grab the bolt out and out comes around bolt.

Does WD-40 Remove rust?

WD-40 can help remove rust from metals like iron, chrome, and stainless steel without further damaging the surface of the metal or removing the paint. The Multi-Use Product is great for loosening and removing excessive surface rust.