How do you repair a hole in a vinyl deck?
When your vinyl deck is damaged, rather than tearing out and replacing the entire membrane, you can heat weld a small piece of vinyl over holes, cuts, or discolourations. To create an effective patch, you’ll need a length of vinyl that matches the pattern of your existing deck.
How do you seal vinyl decking?
Using a poly-urethane caulking such as Masterseal NP-1 will help seal any gaps at the joints. Poly-urethane caulking is a great choice for exterior construction work. Not only does it come in a wide variety of colours, it can also be painted once it has cured. Installed nicely and this is a great waterproof technique.
How do you make a gutter plug?
Quote from the video:
Quote from Youtube video: The petty drop you can use a hole saw. And you can just drill the hole. This is two and three quarter inches.
How do you cap downspouts?
Quote from the video:
Quote from Youtube video: You can just pop out these plugs. And and do your do your thing. You know normally you would have a tuck pointing. Guy cap these with concrete when they do that kind of work.
How do you patch a deck?
Quote from the video:
Quote from Youtube video: Board what i'm going to do is cut five millimeters away from those nails. So i'm going to leave the existing nails in the deck. So what i've done is cut myself a piece of timber.
How do you seal vinyl deck seams?
Quote from the video:
Quote from Youtube video: Squeeze the liquid weld between the overlap seams carefully ensuring that a small amount bleeds out onto the top of the masking tape push. The top piece of vinyl down as you go along.
How do you install waterproof decking?
Quote from the video:
Quote from Youtube video: It is recommended that you plane or sand the outside 2 inches of the deck edge before installing the flashing to create a surface that will not hold dark.
How can I waterproof my deck over living space?
Quote from the video:
Quote from Youtube video: Or over the over a deck or over a living area or over a protected porch area or you can top coat it with liquid granite.
How do you waterproof a deck floor?
Installing a deck drainage system during construction is the best way to waterproof under your entire deck. A deck drainage system diverts water away from the joists and beams. An over-the-joist deck drainage system such as Trex RainEscape provides 100% protection from the damage caused by wood repeatedly getting wet.
Should downspouts go into ground?
Building contractors and plumbers agree that downspouts should go into the ground to tuck them away and maintain a property’s aesthetic. Also, underground downspouts are more effective because they can pair with French drains and sump pumps to throw water far away from the building.
How do you wrap a downspout around a corner?
Quote from the video:
Quote from Youtube video: So again we're utilizing three elbows to get around the corner we're utilizing a b elbow turning an a elbow on its side to go around the corner to the b elbow to get us going back.
How do you install a new downspout?
Quote from the video:
Quote from Youtube video: You can see the eave. And the overhang we need to bring the gutter back of the downspout back to the wall. And then down. So you need several little parts you're going to need a drop.
How do I attach a PVC pipe to a downspout?
Quote from the video:
Quote from Youtube video: What you're going to want to do is slide this on to your downspout. Then apply your PVC glue to the inside of this fitting. And also to your drain pipe stick.
How do you install downspout straps?
Quote from the video:
Quote from Youtube video: Basically all you do you can get them 1/4 inch diameter and then you pick up a quarter inch concrete bit and drill a hole that with this will fit in put the strap.
How do you join downspout sections?
Quote from the video:
Quote from Youtube video: I just grabbed the downspout. Now because it's missing one smaller end and crimp it in you want to pinch in basically on the two smaller sides you want to pinch it in like.
How do you crimp a downspout pipe?
Quote from the video:
Quote from Youtube video: For Piper metal ductwork take the same approach with three blades aligned on the outside of the tube edge and squeeze to make your first crimp.
How do you install downspout elbows?
Quote from the video:
Quote from Youtube video: Section drill and insert two pop rivets on each side. Make sure the rivets penetrate both the straight downspout and the elbow.
