Do deck posts need to be plumb?

Deck posts must be plumb, so they have to start out with square ends. Check the bottom of each post with a speed square and cut it if necessary. Dip cut ends in a preservative before setting them in the anchors and let the preservative soak in overnight.

How do you plumb a deck post?





Quote from the video:
Quote from Youtube video: Use a shovel or 2×4 to remove air pockets. Then fill the rest of the way embed. An anchor bolt into the concrete. Make it plumb and leave no more than an inch of thread showing also backfill.

How far from edge should deck posts be?

Ideal deck post spacing is 8 feet or less. The distance between deck support posts depends on the type of wood species used and the size of the joist and beam.

How far do you sink deck posts?

Set footers a minimum of 6” below the frost line for your area to prevent movement during freezing temperatures. Pour about 6 inches of all-purpose gravel into postholes and pack the gravel tight by using the end of a wooden post.

Should a deck be perfectly level?

In a nutshell, the easy answer is this—no, your deck should never be level with your home. That’s because of the threat most feared by even the bravest DIYers and homeowners: water damage. If your deck or patio sits at the same height as your home, you’re making it easy for water to get inside and wreak havoc.

How do you stabilize deck posts?





To stiffen the deck, go underneath and install a row of 2×8 blocks down the center, perpendicular to the joists. Stagger them with enough room to nail or screw them in place through the end grain, then fasten the treated 2x4s to the underside of the joists so they run from corner to corner, forming an X.

How do you plumb deck railing posts?

Quote from the video:
Quote from Youtube video: Over the bolts. And persuaded the post into position using the hammer. I added a washer and nut to each bolt. And then tapped them even deeper into the wall to maximize the anchoring strength.

Why deck posts should not be set in concrete?

Deck posts set in concrete increase rot and make it impossible to replace the post in the future if it is damaged. Also, in many jurisdictions, setting deck post in concrete is illegal; instead, deck posts need to be placed above the concrete footing extending below the frost line to 6″ (150mm) above grade.

What size footings do I need for a 6×6 post?

FOOTINGS: – Poured concrete footings should be a minimum of 8” wider than the posts (4×4 post – 12” min. width, 6×6 post – 14” min. width), a two level deck or deck with roof – 24”x24”. – The bottom of the footings must be a minimum of 36” below finish grade level.

How far from house should deck post be?



Deck footing for 2×6 and 2×8 joist should be 16″ (400mm) from the house. Deck footings for 2×10 and 2×12 joist should be 24″ (600mm) from the house. There are several reasons for distance between the house and the deck footings. Space is both for ease of installation as well as strength of deck construction.

How deep should 4×4 deck posts be?

Dig post hole so diameter of the hole is 3 times the width of the post (i.e., the hole for a 4” wood post should be about 12 inches wide). The depth of the hole should be 1/3-1/2 the post height above ground (i.e., a 6-foot tall fence would require a hole depth of at least 2 feet).

How many posts do I need for a 12×16 deck?

As a guide, if you choose to use 20-foot boards, you will need to purchase 22 of these boards. Similarly, 18-foot boards will require 24 boards, 16-foot boards will require 27 boards, 14-foot boards will require 31 boards, 12-foot boards will require 37 boards and 10-foot boards will require 44 boards.

How much slope does a deck need?



With a slope, the water is able to run off and drain sufficiently. You need to make sure that the slope is not noticeable but sufficient enough to do the job of draining. Most contractors suggest sloping the deck 1/4th- 1/8th of an inch for every foot of decking.

How far below a threshold should a deck be?

There’s no magic number, but I would recommend a minimum of 2 in. from the top of the decking to the bottom of the patio door threshold. I opted for 3-1/2 in. Many doors have a sill or threshold that needs to be supported, so don’t forget to install a kick plate under the door.

Does a deck have to slope?

Quote from the video:
Quote from Youtube video: Похожие запросы

How do you square a deck post?

Quote from the video:
Quote from Youtube video: Okay for example if you measure back to 10 feet from the house. And you measure along the house 10 feet. So you have your a and your B sides. So 10 times 10 is 100. 10 times 10 is 100.

How can I make sure my post is same height?



Center one post in each hole. Combine quick-setting concrete mix with water in a wheelbarrow to form a thick, wet concrete mixture. Fill the hole around each post with the wet concrete mixture, keeping each post vertically straight. Allow the concrete mixture to set for four hours.

How do you shim a deck post?

Quote from the video:
Quote from Youtube video: And then i'm going to finish tightening down these screws after the post is plumb. And you've tightened all the screws. You can take a razor knife. Or even a hammer and a chisel i like to score.

How do you level a post?

Quote from the video:
Quote from Youtube video: So we need to manipulate the posts so there they're all plumb equal distance from each other and square. So now with this trick we can actually do it quite easily and then we can brace it permanently.

Can you put dry concrete in a post hole?

Quote from the video:
Quote from Youtube video: Because there is no mixing you simply pour it into the hole. Dry. Then add water when digging your post hole it is important that the diameter of the hole be three times the width of the post.

How do you level posts on uneven ground?



Racking Fence

  1. You will stagger the posts down the slope, so measure out how far apart they need to be a part, which is usually between 6 to 8 feet.
  2. Dig the hole for your post, about one-third of the post or 2 feet deep.
  3. Pour in your gravel, about 6 inches, at the bottom of the hole.
  4. Insert your post.
  5. Pour the concrete.

How deep should post be driven?

The general rule of thumb when setting a post is that the depth of the post’s hole needs to be one-third to one-half of the actual above-ground height of the post. So, a six-foot-high finished post ideally needs to be buried three feet into the ground.

How deep should a 6-foot post be in the ground?

The depth of the hole should be 1/3-1/2 the post height above ground (i.e., a 6-foot tall fence would require a hole depth of at least 2 feet). Add about 6 inches of QUIKRETE All-Purpose Gravel into the bottom of the hole. Then compact and level the gravel using a post or 2×4.

How deep should an 8 foot post be in the ground?

about 2 feet deep

For an average fence post, about 6 to 8 feet tall, prepare to dig a post hole about 2 feet deep. To install a fence post, you’ll need a shovel or post digger, a 6-foot level, soil, and gravel or crushed stone.