How do you wire a switch when the power is at the light?

Quote from the video:
Quote from Youtube video: You were allowed to use a two wire cable for this so there's many situations out there where this is the case you only have a black and a white coming down from the light fixture to the switch.

How do I connect my Juno lights?





Quote from the video:
Quote from Youtube video: App launched the juno AI app on the welcome screen select register to create a login.

How do you light an LED switch?

Quote from the video:
Quote from Youtube video: If you wanted to switch the light on and off simply add an on/off switch between the fuse and the light as.

How do you install a Juno wafer downlight?

Quote from the video:
Quote from Youtube video: Close the cover of the box connect the remote driver box to the light fixture. And tighten the nut connector by hand the arrow on the male and female parts of the connector. Between the driver.

How do you run power to a switch?

Quote from the video:
Quote from Youtube video: So you have a hot that comes all the way in goes through the switch up to here and you have a neutral that comes all the way and goes back to the panel you have a complete loop.

Does it matter which wire goes where on a light switch?





In the case of a single-pole switch, these wires are interchangeable—it doesn’t make any difference which wire is attached to which screw terminal. Inside the switch is a metal pathway that closes when the switch is in the ON position and opens to interrupt the flow of power when the switch is turned OFF.

How do I connect Juno connect lights to Alexa?

How do I add a new Juno AI Speaker light or downlight to an existing Alexa controlled installation? Open the Juno AI app and follow the instructions for commissioning the fixture and enabling Alexa skills. Then, open your Alexa app and your Juno AI fixture will now be part of your existing system.

How do you wire a wafer light?

Quote from the video:
Quote from Youtube video: First we're just going to put our copper wire. Into the hole. And you're just going to push it in feel that when it locks you so the same thing i'm just going to insert it and push it in it's super.

How do you install LED downlights?

Quote from the video:
Quote from Youtube video: The driver cover then clips onto the driver box with the two cables gripped by the cover as it snaps on. The other end of the driver has a wire with a clip on the end.

How do you wire LED recessed ceiling lights?



Quote from the video:
Quote from Youtube video: So all you have to do is strip the wire plug that in all the greens go in one all the blacks on another. And all the whites. On the last one. And then you can just screw these two together.

How do you wire an LED?

Quote from the video:
Quote from Youtube video: Let it focus there we go the negative side of the LED leg is shorter than the other see that so the shorter side is the negative lead in the longer side is the positive lead.

How do you wire a recessed light?

Quote from the video:
Quote from Youtube video: To run through the circuit of all the recessed lights my additional white one no my neutral is just gonna tie in with the neutral here and then the neutral that's on the fan.

How do you install LED lights on a ceiling?



Five steps to install LED strips

  1. Decide what kind of lights you want. …
  2. Plan the route, locate a power source, and measure for length of strip. …
  3. Check your ceiling type. …
  4. Install the LEDs on the ceiling. …
  5. Connect the LED strips to power.


How do you connect LED strip lights to power supply?

Quote from the video:
Quote from Youtube video: To fit the connector. Gently pull back the black locking bar insert the tape into the slot until it is fully located. And ensure that the copper connection points are within the body of the connector.

How do you use LED light connectors?

Quote from the video:
Quote from Youtube video: So open the connector you will notice that there are two metal contacts in the connector. Gently insert the strip into the connector. Make sure the strip goes below the ridges on either side.

How do you connect LED lights to a room?



Quote from the video:
Quote from Youtube video: It open and put them on high so what's included in the box is the AC adapter. So this plugs into the wall. This end goes into here.

How do you connect LED strips without connectors?

Quote from the video:
Quote from Youtube video: You know connectors on the other light strip. And then you're gonna use the sticky. Thing. Yeah whatever that's called to stick it down and do that for both sides.

What happens if your LED lights won’t turn on?

If the LEDs will not light up at all, then this could be down to a faulty power supply. If you have several power supplies, then try a different power supply onto the same strip to see if this now works. If it does, then you have a faulty power supply and will need a new one.