How do you adjust ceramic taps?
Quote from the video:
Quote from Youtube video: Make sure that you separate the locking up from the ceramic cartridge spindle and shown here. This is what your parts should look like important and not until the base of the ceramic cartridge.
How do you remove a ceramic tap cartridge?
Quote from the video:
Quote from Youtube video: So let's have a go in there they'd have a small screwdriver. It does the job. Take that off and now the next tricky bit is we've got to get into there to undo. The inside of the tap.
How do you fit a mixer tap cartridge?
Quote from the video:
Quote from Youtube video: Now remove the old cartridge. And insert the new cartridge by locating the two plastic pegs on the back of the cartridge into the seating of the tap body once the new cartridge is in place replace.
How do you change a single tap cartridge?
Quote from the video:
Quote from Youtube video: Below with water. So we're going to change the cartridge in this tab. New cartridge looks like that's so you've simply got a ceiling ring at the bottom. And then you've got the lever on the top.
Can ceramic disc taps be repaired?
Ceramic tap cartridge repair or replacement. Before conducting this process, please check with your local plumber (or get in touch with our expert team here) that you have acquired the correct replacement ceramic disc catridge. To repair or replace a ceramic disc cartridge you will need: New ceramic tap cartridge.
How do you remove a ceramic tap spindle?
Quote from the video:
Quote from Youtube video: Now the traditional washers might have swirled a little bit so you might need to get just some long pliers just to get that out. And then you can see the traditional.
How does a ceramic tap cartridge work?
Ceramic disc cartridges are simply two ceramic discs with holes through them. One disc is fixed in place whilst the other moves with the tap handle. When both discs are in alignment, the water is allowed to flow through the tap. When they are no longer aligned, the water stops.
Are ceramic disc taps any good?
Plumbing connections for ceramic disc are no different to other taps, and with that comes all the ease of a quarter-turn technology, and a more durable, longer lasting tap without those annoying leaks. From a long-term maintenance point of view, ceramic disc taps are much better than normal taps.
How do you measure a tap spline?
Tip: The easiest way to count the number of teeth on a spline is to place a pencil mark in one of the grooves, then place your fingernail in that groove and rotate the shaft. Count how many ‘clicks’ there are until you return to your pencil mark.
Are ceramic tap cartridges handed?
The quarter turn is normally ‘handed’ when a pair are purchased – i.e. one tap turns clockwise to open, while the other tap turns anticlockwise. This can take some getting used to. There are a number of advantages with using ceramic discs instead of rubber washers.
Is there a difference between hot and cold ceramic tap valves?
In other words both the Hot and Cold valves are the same but open in mirror directions so please select the valve you require according to how your taps work. If you have a two lever ‘filterflow’ or ‘aquifier’ tap then the hot side has a valve and the cold side has a diverter cartridge for the cold and filtered cold.
What is the difference between hot and cold ceramic cartridge?
Although Kohler ceramic valve cartridges are available in hot (which means the water turns off by turning the handle clockwise) and cold (the water turns off counterclockwise), the only difference between the two is the way the valves turn.
Are ceramic disc cartridges interchangeable?
Chicago Faucets ceramic disc cartridges are interchangeable with compression stems and were designed to prevent water hammering. Ceramic stems are recommended in newer buildings with copper lines or when water hammer occurs in compression units.
How do I know what cartridge my faucet is?
Quote from the video:
Quote from Youtube video: Okay so the easiest way to figure out what brand of faucet you have is to look on the outside to see if you can find the logo or the name brand of the manufacturer.
Are tap valves universal?
Tap glands are also known as tap valves and typically sold in pairs. In some cases the same gland can be fitted to either the hot or cold tap as they open in the same direction. If you’re replacing a old tap gland, make sure you measure the diameter to ensure you purchase the correct size.
Are all kitchen tap valves the same?
Most of our valves are 7.6mm dia which is by far the most common diameter size, and fits onto the most common tap handle hole size of 8mm. However, some valves do have a narrower or wider spline diamater.
How do you disassemble a mixer tap?
Quote from the video:
Quote from Youtube video: But you will need to turn the water off before you go any further otherwise you'll have a fountain running in the middle of your sink. So set this down again and we'll pull this apart.
