Disconnect the macerator from the electric supply. Pour 1-2.5 litres of Toilet Cleaner & Macerator Descaler into the toilet bowl. Turn the macerator pump on for a few seconds to allow the descaler to enter the macerator.

How do you use Saniflo descaler cleanser?

Easy to Use.

  1. Pour half the bottle, or approximately 2.5 liters, of the descaling solution into the toilet bowl.
  2. Leave the solution for at least two hours.
  3. Connect the unit to the power supply. Flush the toilet a few times.





How do you flush a macerator toilet?

Quote from the video:
Quote from Youtube video: Using the provided discharge elbow connect your three-quarter inch discharge pipe then connect the toilet to the main inlet of the pump. Using. The 4 inch coupling provided.

Can you use bleach in a macerator?

Alternatives simply don’t do as a good a job, and can in fact damage the internal operations of the unit. For example, regular use of ordinary household bleach or other toilet cleaners will damage the rubber membrane which covers the pressure switch that governs when your SANIFLO macerator unit turns itself on and off.

What can I use to clean my Saniflo toilet?

You can also use white vinegar or preferably, Saniflo descaler to do this: disconnect your fixture from the power supply, then pour 2 litres of product in the bowl of your toilet. Leave it to work for a few hours and then reconnect to the power supply and flush.

How do you use macerator cleaner?





Pour approximately 1.5-2 litres of the bottle down the toilet and flush. Allow it to stand for 2-3 hours or preferably overnight to allow a complete descale of the tank. After this period, turn the Macerator back on and the system will be cleaned from within. Allow the unit to pump out and then flush the toilet.

How do you descale a Saniflo macerator?

To clean your Saniflo thoroughly, follow the below steps:

  1. Turn off the power to the unit.
  2. Pour a dose of descaler into the pan.
  3. Flush the toilet.
  4. Leave for 1-2 hours.
  5. Turn on the power and let the unit pump out.
  6. Flush again.


Can you use sink Unblocker in Saniflo?

Chemicals should NOT be used on saniflow systems as it can damage the seals inside (nor plunge them), if all else is draining fine then as above check the waste in the shower.

How much water does a macerator toilet use per flush?



1 .7 liters

(1 . 7 liters) per flush and does not add water to the bowl . Versatile installation. Powerful macerator pump allows toilet to be located up to 98 ft .

Can you plunge a macerator toilet?

Can you plunge a macerator toilet? If you have a blockage with your Saniflo or macerator toilet it’s not as simple as using a plunger to unblock it. Using a plunger on a macerator toilet could damage the macerator system so if there is a blockage it will need to be taken apart and cleaned.

What can you put down a macerator?



Toilet Cleaner & Macerator Descaler works as a general toilet cleaner as well as to clean and descale macerator tanks. Our formula contains phosphoric acid, which works to break down limescale and dirt, whilst being gentle enough for the macerator system.

Why does my macerator toilet smell?

Bad smells can be due to a build-up of limescale and human waste in the 2-3 inches of water that’s always left in the Saniflo. To see if it’s your Sanilfo that’s emitting the bad smell, flush your toilet or fill your basin with water and then unplug it.

How often should I descale my Saniflo?

It is recommended that Saniflo Descaler is used for up to 3-4 times per year depending on water hardness in your area. Most of our work is in London and the water is seriously hard in some places. So we ourselves recommend you descale a Saniflo 3 times per year. experience start stop problems around the 4-5 year mark.

Can you use vinegar to clean a Saniflo toilet?

Yay! Show activity on this post. I’m a Saniflo repair specialist in the UK, don’t use vinegar or other concoctions like Coca-Cola etc to clean out a Saniflo macerator as it does not work. Saniflo’s that are not descaled will eventually start misbehaving.

What happens if you put baking soda in the toilet?



After you’ve poured the baking soda and vinegar in the toilet, pour a pot or kettle of hot water down the toilet. Take a look and see if the clog has been released. If it has released, it will make a suction sound and it will drain normally. Flush the toilet once or twice to make sure it’s working correctly.

What does baking soda in toilet tank do?

Clean the Toilet Regularly



There is no need to use harsh and costly chemicals to prevent hard water toilet stains. Borax, vinegar, and baking soda do a great job of cleaning and disinfecting. Used regularly, they will prevent hard water stains from building up.

Will vinegar hurt a water pump?

Vinegar is a powerful acidic substance. Its enzymes help break down the toughest grime, dirt, and grease. It’s not only an effective cleaning solution for floors, tiles, and bathtubs but also a fantastic sump pump cleaner.

Can I put baking soda in my fountain?

A solution of distilled white vinegar and water can vey very helpful in cleaning the fountain surface. If you have a tough spot of scale that doesn’t want to budge, make a paste of baking soda and water and let it sit in there a bit.

Can you put bleach in sump pump?



A DIY remedy to remove sump pump odors is to use a bleach solution in the sump pit. Create a diluted bleach solution, 1 cup bleach for every 1 gallon of fresh water. Pour the solution into the sump basin until water volume activates the float switch and the sump pump turns on.