As for that pivot nut, if you really want to remove it, it USUALLY is easy enough to unscrew with your bare fingers, but if it is rusted you can use a pair of channel lock pliers. If it is just spinning however, it may be all the way off the threads and you just need to pull it back.
How do you loosen a pivot nut?
Quote from the video:
Quote from Youtube video: Turn it just enough just so I can get my hands on there. And you know loosen that up. Once you loosen that nut up. You can pull that little rod out it's that little plunger. Okay pull that out.
How do I remove the stopper from a pivot rod?
Quote from the video:
Quote from Youtube video: The position where the pivot rod. Goes through the strap. Then mark the other end of the lift strap where it connects to the lift rod to the faucet.
How do you loosen a sink stopper nut?
- Spray bathroom cleaner on the stuck nut and wipe up with a towel or rag. …
- Spray the nut with penetrating lubricant. …
- Tap the side of the lock nut with a hammer. …
- Clamp a pair of locking pliers around the nut and lock into place. …
- Heat the nut with a plumber’s torch. …
- Slip a nut splitter over the lock nut.
- Set the drain to its open position.
- Lift up on the drain stopper’s knob and turn it counterclockwise.
- After enough turns, the drain stopper should be unscrewed and come free from the drain opening.
- Start by pouring a pot of boiling water down the drain.
- Next, pour a cup of baking soda and 1 cup water/1 cup vinegar solution.
- Cover with the drain plug and wait 5 to 10 minutes.
- Pour boiling water down the drain again.
How do I get my bathroom sink stopper unstuck?
Quote from the video:
Quote from Youtube video: Video i said put on a rubber glove. And just push. Down. As hard as you can with the rubber glove. So you got grip. Turn counterclockwise. And it pops up see.
How do you remove a stuck lock nut?
Quote from the video:
Quote from Youtube video: I've got a steel tip on the back for striking it and that's steel core goes all the way through. So you don't damage the tip.
How do you loosen a plastic locking nut?
One of the best ways to remove a difficult lock nut is by using plumber’s grease. Simply apply the plumber’s grease to lubricate the plastic nut, then let it sit for 10 to 15 minutes. Once that has sat for a while, attempt to remove it using your hands or a pair of pliers.
How do you remove a push pull drain stopper?
How to Remove a Push-Pull Drain Stopper:
How do you remove a lift and turn stopper without a screw?
Quote from the video:
Quote from Youtube video: Because it's still in a groove. You're gonna pull it up just enough to where you can grab hold of this larger. Piece then you're gonna unscrew this larger piece you felt it give there.
How do you open a drain plug?
Quote from the video:
Quote from Youtube video: But just letting it drop in and then without lifting it very high while it's still engaged. You're going to turn it in a counterclockwise direction. So that it will unscrew.
How do you unclog a lift and turn drain?
Quote from the video:
Quote from Youtube video: And just screwdriver for that there's a little slot in here just stick the screwdriver in to turn it just keep turning until the shaft inside the stoppers loose.
Does baking soda and vinegar dissolve hair?
Use Baking Soda & Vinegar Before Plunging It Out: Baking soda and vinegar can be an extremely effective way of dispatching many clogs, and hair clogs are no exception. For best results, start by squirting a little dish soap into your drain, followed by a cup of vinegar and a cup of baking soda.
How do you unclog a bathtub drain with baking soda?
4 Steps to Unclog Your Drain with Baking Soda & Vinegar
