How do you get a pipe unstuck from another pipe?
Quote from the video:
Quote from Youtube video: If you can't get the pipe fitting apart using heat try grabbing a hammer and tapping all around the outer ring of the fitting.
How do you loosen a corroded pipe?
Quote from the video:
Quote from Youtube video: Wd-40 multi-use products are great for disconnecting damaged rusty pipes.
How do you separate two pipes?
Quote from the video:
Quote from Youtube video: So i formed two halves with it split. It and that'll loosen up the pipe. And you get it off obviously you'd have to replace the fitting. And it could go on and on and on.
How do you unstick metal pipes?
Quote from the video:
Quote from Youtube video: Part are angled upwards so they will dig. Into the nut as we loosen it and then these teeth on the claw side the movable side see see how they're angled downward like this they will dig into the nut.
How do you separate cast iron pipe joints?
Tap the handle of the screwdriver with a hammer to drive the tip under the lead to pry it out. Pry out the oakum packing below the lead, using the screwdriver. Pull apart the connection. Repeat the procedure to disconnect other sections joined with lead and oakum.
How do you extract brass fittings?
Quote from the video:
Quote from Youtube video: It's that simple and simply to get these off you would go clockwise. And they'll loosen themselves and there you go guys.
How do you remove corroded brass nuts?
Heat the nut with a propane torch, taking care to avoid any adjacent flammable surfaces. The heat may expand it so that it will loosen. Tap the nut with a hammer to attempt to break the corrosion which is binding the nut.
Can I connect brass to galvanized steel pipe?
To safely connect copper and galvanized steel, you have two options. Since brass doesn’t react with either the copper or the zinc, one method is to make sure you have a threaded female end on both the copper and the steel pipes, and then connect the two by simply inserting a short threaded brass nipple between them.
How do you remove compression fittings from brass?
Quote from the video:
Quote from Youtube video: And place the forks of the puller behind the compression ring and nut. Next turn the puller handle clockwise until the compression ring and nutter pulled loose from the copper.
How do you remove cast iron pipe fittings?
Quote from the video:
Quote from Youtube video: So when i heated it up when i was heating this lid. Up i knew the flame couldn't get past the packing. So i just heated the lid. Up let the lead melt out once i got down to the packing.
How do you break cast iron pipes with a hammer?
Hit the back of the chisel with a hammer. Move the chisel along the cast iron pieces while striking it with the hammer until the larger pieces break. Continue with the chisel and hammer until the cast iron breaks into manageable pieces.
How do you remove a stuck cast iron plug?
How to Loosen a Cast Iron Clean Out Plug
- Spray lubricant around the rim of the plug, aiming the spray to get as much of it into the threads as possible. …
- Tap the rim of the plug a few times with a hammer to loosen the threads, instructs Family Handyman.
What’s the best way to cut cast iron?
Quote from the video:
Quote from Youtube video: How to cut cast iron sewer pipe you can use either a grinder or reciprocating. Saw i prefer a reciprocating.
Can cast iron be cut with a hacksaw?
Hacksaws
If you have a good, old-fashioned hacksaw, you can use it to cut your cast-iron pipes. But keep this in mind: using this tool requires you to exert maximum effort and can result to a lot of hard work. It also takes a substantial amount of time, especially if you have several pipes to cut.
Can I use a grinder to cut cast iron pipe?
The one tool you can use and likely have on-hand is an angle grinder. While you could use a reciprocating saw or even a hacksaw to vigorously slice your way through cast iron, utilizing an angle grinder to swiftly cut segments of cast iron pipe, is a viable option too.
