How do you wire a ceiling fan with a light switch and a dimmer?
Connect the incoming red as live wire to the single way switch. The other end of the SPST switch should be connected to the combine dimmer and speed regulator switch. Now connect the upper left end of the regulator switch to the red wire of fan and connect the upper right end of the dimmer to the blue wire of light.
Can you put a dimmer switch on a ceiling fan with a light?
Standard dimmer switches should never be used to control the fan motor on a ceiling fan because the dimmer could damage the fan motor, or overheat and start a fire.
How do you wire a dimmer to a ceiling light?
Installing a Dimmer Switch
- Select a dimmer switch that has a rated capacity high enough to handle the combined wattage of all the bulbs in the chandelier added together.
- Turn the power off to the fixture at the breaker.
- Remove the cover and existing switch.
- Attach the dimmer to the wires using wire nuts.
How do you get a light and fan switch on separate switches?
Separate switches for ceiling fan and light
- take the 2 wires on the switch that controls the outlet off the switch, twist them together in a wire nut, and push them into the back of the box. …
- In the ceiling, connect the red hot wire to the blue wire controlling the fan.
Can I use a light switch for a fan?
Most new ceiling fans can be wired to either a single switch or a double switch. With single-switch wiring, power to the fan is controlled by a standard single-pole wall switch, like a regular light switch.
How is a dimmer switch wired?
New dimmers have either a green grounding wire or a green ground screw that you’ll have to connect to a grounding source if one is available. Houses wired with plastic-sheathed cable almost always have bare copper ground wires that you’ll connect to the toggle dimmer switch.
How do you wire a fan light switch combo?
Quote from the video:
Quote from Youtube video: The light to the fan fixture. That is the blue wire up to my red wire. And then my neutral which is the white wire to the white wire and the green which is your ground to the copper wire.
How do I separate multiple lights on one switch?
3 Answers
- Get a 2-gang box to replace your existing 1-gang box.
- Get a new switch.
- Remove your existing box and install the 2-gang box in its place.
- Run your supply hot wire to both switches.
- Connect the light/fan hot wire to one switch and the exterior light to the other.
- Join all neutrals and ground wires.
Can a bathroom fan and light be on the same switch?
You can run your bathroom fan on the same switch as your lights. It solves other problems, so it’s not a bad idea even if you have two switches.
Can you put a bathroom fan on a dimmer switch?
So it appears the fan should be fine. But there is some risk to the dimmer due to voltage spikes generated by the inductive load. You could try to find a dimmer switch that is rated to control inductive loads, or you could just try it out.
What is code for bathroom exhaust fan?
Section R303.
When this section is adopted by a community, it essentially says that, for venting purposes, bathrooms must have windows that open. The code reads that the window must have “aggregate glazing area…of not less than 3 square feet (0.3 m2), one-half of which must be openable.”
Do I need a special switch for bathroom fan?
Thanks! If it’s a typical small one speed bathroom fan you can use any on/off switch that matches the load specs; just don’t use a dimmer switch intended for lights. If it’s a large ceiling fan or a variable speed fan, then you need to use one of the purpose – built fan switches: both Leviton and GE make these.
How do you wire a bathroom fan to an existing light switch?
How to Wire a Bathroom Fan to an Existing Light
- Shut Off the Power. …
- Remove the Light. …
- Remove the Wire Connectors. …
- Run a Cable to the Housing Box. …
- Wire the Cable to the Fan. …
- Use a Wire Stripper to Remove the Cable’s Outer Sheath. …
- Attach the Black, White and Neutral Wires. …
- Restore the Power.
Can I use smart switch for bathroom fan?
The SmartExhaust™ is designed to replace the bathroom fan and light switches with one smart controller and features programmable settings for running the exhaust fan as much or as little as you want, automatically.
How do you wire a bathroom fan and light on separate switches?
Quote from the video:
Quote from Youtube video: But these are both on the same circuit so we leave the tab. And you just put the black wire to one of the two black common terminals on the other.
