Can you put vinyl plank flooring over plywood subfloor?

Can I install vinyl flooring over wood, plywood, particleboard or chipboard? You can install vinyl over wood floors if you put a plywood subfloor on top of it. Do not install glue down or peel and stick products over particleboard, chipboard or any form of embossed floor.

How do you prepare subfloor for vinyl plank flooring?





5 Simple Steps to Prepare a Subfloor for Vinyl Flooring

  1. Step 1: Test the Floor for Moisture. …
  2. Step 2: Repair Holes and Cracks. …
  3. Step 3: Sand Down Bumpy Areas. …
  4. Step 4: Clean the Subfloor. …
  5. Step 5: Install Underlayment (Optional)


How do you prepare plywood for vinyl flooring?


Quote from Youtube video: Even if you have to put down a primer on top of it to make sure that you seal all that dust. After your floor is clean you're going to take your tape measure.

Should I seal my subfloor before installing vinyl plank flooring?

Subfloor sealing is not required. It is not even recommended, but if bonding is a concern, dont seal the subfloor. Instead, use some clear-set thin-spread vinyl tile adhesive to aid the tile in bonding to the subfloor.

How smooth should subfloor be for vinyl planks?





SUBFLOOR REQUIREMENTS



Subfloor must be clean, structurally sound/tight, and visibly dry. Floor must be flat to within a 3/16” in 10′ radius tolerance.

How do you install plywood underlayment for vinyl plank flooring?

Quote from the video:
Quote from Youtube video: This direction my 4 foot will come from this cabinet over that way my 8 foot will go from the sink area over that direction first of all I want to make sure that my underlayment.

Do I need underlayment for vinyl flooring on plywood?

Plywood Subfloor



There’s no need for a moisture barrier underlayment on plywood. It’s more important that the underlayment dampens sounds and feels comfortable. An underlayment that offers more cushioning is Armstrong® Flooring Quiet Comfort™.

How do you prepare a floor before laying vinyl?

Quote from the video:
Quote from Youtube video: First of all remove all existing soft floor coverings such as carpeting belt and vinyl hard floor coverings such as tiles and linoleum can stay in place unless there are too many irregularities.

What type of underlayment do you use for vinyl plank flooring?



The rule of thumb is any vinyl over 4mm can have a vinyl specific underlayment. With thinner vinyl flooring construction, adding a foam underlayment can effect the locking system strength. Vinyl floors under 4mm should be installed right over the subfloor.

Does plywood subfloor need vapor barrier?

Manufacturers Require a Vapor Barrier



Your plywood subfloor may look dry, but after you install the flooring, moisture can migrate up through the subfloor and penetrate the flooring, and the results are usually disastrous.

Should you put a vapor barrier between subfloor and underlayment?

Therefore, because concrete is porous, it’s a good idea to install a vapor barrier over your concrete subfloor before installing your flooring. This way you can stop the vapor drive of water upward to your floors, protecting them from any damage (source).

Can vinyl plank flooring be installed on subfloor?



Any type of flooring can benefit from an underlayment — even luxury vinyl tile. This holds true no matter what type of subfloor it will be installed on, including concrete, wood flooring, or any other type of flooring. Underlayment can improve the vinyl tile’s ability to absorb sound.

How flat should subfloor be for floating floor?

Most manufacturers recommend that the floor be flat to within 3/16” in a 10 ft. radius. These measurements are consistent with most other types of floor coverings. On floating floors, vertical movement needs to be kept to a minimum.

How thick should plywood be for vinyl flooring?

1/4″ thick

When you install your vinyl on a wood subfloor, the top plywood should be a minimum of 1/4″ thick. For most subfloors, you will need to add an extra layer of wood. To do this, measure and cut the plywood to fit your room.

Will vinyl stick to plywood?



Actually unsealed wood, plywood and even painted plywood are not good substrates for vinyl. Vinyl is an adhesive backed film that is expected to last for years outdoors in all kinds of weather. To achieve that longevity, the adhesive must have a firm bond with the substrate.

What kind of plywood goes under vinyl flooring?

Plywood underlayment is a thin plywood material that is most commonly used under resilient flooring materials, such as vinyl and linoleum sheets and tiles.

What is the best plywood to use under vinyl flooring?

APA-rated Sturd-I-Floor plywood is ideal for underlayment when the surface is integral to how your flooring will perform. Blemishes and flaws could cause uneven wear and tear or damage to your flooring if it’s not sitting flush. This is especially important with vinyl and adhered carpets.

How thick should subfloor plywood be?

The minimum thickness of plywood for subflooring is about 5/8 inch. Since it does not hold fasteners as well as plywood, OSB must be a little thicker, or at least 23/32 inch.

How thick should underlayment be for vinyl flooring?



1mm to 1.5mm thick

Most vinyl underlayments are 1mm to 1.5mm thick. When dealing with a click lock vinyl of 4mm or thicker, an underlayment has several benefits: It can help smooth over minor subfloor imperfections. It will add extra cushion to the floor, creating a softer feel under foot.