How do you hang things on Hardie board siding?

Generally speaking, items can be attached to Hardie® siding by using either corrosion resistant nails or screws. The fasteners must be long enough to go through the siding and into wood or metal substrate (e.g. sheathing or studs).

How do you mount something to Hardie plank?





Our Answer. The best way to attach to Hardie Plank siding is by using nails or screws. To avoid cracking the siding, pilot drill the siding first, using drill bit a little smaller than the nail or screw. And to make the sure the hole you are forming doesn’t leak, caulk the hole before driving in the fastener.

Can you screw things into hardiplank?

Can You Screw Things into Hardie Board Planks? Yes, you can, provided that they’re light enough. Anything weighing less than one pound (half a kilogram) can be attached directly to the Hardie Board. If it’s heavier than a pound, you’ll need a stud finder and attach whatever you’re hanging to this stud.

How do you hang lights on hardiplank?

Quote from the video:
Quote from Youtube video: You just drill a little hole in the hardy. And go into the wood behind it and that would be perfectly.

Can you screw into fiber cement siding?

Fiber cement siding can be nailed by hand or with a pneumatic nailer. It can also be attached using corrosion resistant screws. Use hot-dipped galvanized or stainless steel nails. Nails should penetrate through the sheathing and at least 1” into studs.

Can you drill holes in hardiplank?





The siding is fire-resistant, providing a high level of protection for a home. HardiePlank is available as ready-to-paint or with a color layer. Although the siding does not require drilling pilot holes, you may need to run wire or cable through the siding, necessitating drilling a hole.

How do you anchor into cement board?

Quote from the video:
Quote from Youtube video: Where you notice on the wood it's a high low thread. And that high low thread helps get that screw through cement. I mean it's a cement board screw.

What screws to use on hardiplank?

HardiePlank® lap siding may be used with fasteners approved by ICC-ES ESR-2290 spaced in accordance with the Wind Load Tables. Fasteners must be corrosion resistant, galvanized or stainless steel.

How do you drill through Hardie board?

It can be cut and drilled just like wood. However, drilling through cement-fiber siding goes better if you use a carbide drill bit, as opposed to a regular steel drill bit. Cement-fiber siding can be drilled while installed on a house or prior to installation.

Can you use Command hooks on Hardie board?



Command™ Outdoor Products can also be used on smooth, sealed and finished surfaces including vinyl siding and fences, doors, windows, decks, gutters and trim. The Outdoor Product line is not recommended for use on rough surfaces, such as cement board, brick or rough-sawn wood.

How do you hang lights without damaging siding?

OPTION 1 – Siding Hook



This is the most efficient method. Slip the top of the hook underneath a piece of siding and wiggle it until it “snaps” into place. This hooks it onto the bottom of the siding. Then hang your decorations on the bottom of the hook.

Can I attach string lights to siding?

If you have siding or brick you will need to drill a little hole to get it started. Again we secured the lights with a zip tie. That round hook was already in our house!

How do you attach outdoor lights to siding?



Quote from the video:
Quote from Youtube video: So we're just gonna go ahead and feed these wires back through this plate like so and you see this plate has notches here it's designed to go against the siding. And we're just gonna slide it up into.

How do you attach string lights to the side of a house?

How to Hang Outdoor String Lights

  1. Step 1: Measure & Prep. The first thing to do is measure for both your string lights and the cable guide wire you need for spanning across any open spaces. …
  2. Step 2: Mount Screw Hooks. …
  3. Step 3: Connect & Tighten Cable. …
  4. Step 4: Attach Your String Lights. …
  5. Step 5: Sit Back and Enjoy!


How do you attach bistro lights to siding?

If you want to hang your cafe lights from your house or another wall or fence, simply drill a pilot hole and screw either an eye hook, a cup hook, or a coaxial staple into the wall. What is this? We used this method on the house side of our patio. I hung string lights on the wall behind my new boho porch swings!

How do you hang things on vertical siding?



Using clips or hooks is a better way to attach things to vinyl siding.



Any of the following options will work well to hang things from vinyl siding:

  1. Siding hooks.
  2. Suction cup hooks.
  3. Adhesive hooks.
  4. Wire hooks.


How do you hang outdoor lights without nails?

The best ways you can hang patio lights without nails is using gutter hooks, adhesive hooks, clear tape with a strong and reliable hold, using a hot glue gun, or staples to hang the lights. Other methods include zip ties, wrapping the lights around pot plants, or attaching them to the trees.

How do you hang fairy lights without nails?

How to hang lights in a room without nails

  1. Use adhesive clips. With damage-free adhesive hooks or clips, you can deck the halls without nails or stress. …
  2. Drape on furniture. …
  3. Wrap around banisters. …
  4. Use brick and brick clips. …
  5. From a curtain rod. …
  6. Transparent tape. …
  7. Wrap around household objects. …
  8. Staples.

How do you hang lights on a concrete wall without drilling?



Hanging Outdoor Christmas Lights Without Drilling Holes in Concrete Stucco

  1. Shingle or Siding Tabs. Some stucco-covered homes still feature portions of the outdoor walls equipped with wooden shingles or vinyl siding. …
  2. Gutter Hooks. …
  3. Magnetic Hooks. …
  4. Suction Cup Hooks.


How do you hang fairy lights with Command Strips?

To attach the Command™ Outdoor Light Clips, remove the blue liner and press the adhesive strip firmly to the back of the clip. Then, remove the black “wall side” liner and press the clip to window. Press firmly along the entire clip for 30 seconds and wait one hour before use.