How far can a washing machine be from the drain pipe?
For new Top Load washers, the drain hose should be no more than 5″ down into the drain pipe. For Front Load washers, the drain hose should be no more than 7″ down into the drain pipe.
How far can a washer be from a vent stack?
4 feet
It prevents the possibility of a vacuum forming which could affect the water draining from your washing machine. If your washing machine is more than 4 feet from the vent stack, you should install a vent to make sure there’s enough room for the machine to drain properly.
Can you extend the waste pipe on a washing machine?
Washing machine waste pipe extensions are used to replace or extend an appliance drain hose, which connects to a washing machine or dishwasher to empty the used water to a standpipe or u bend.
How do I extend my washer standpipe?
That isn’t difficult either — remove the ring entirely, wrap some rope packing around the pipe just above the junction (or install a new packing washer, depending on the age of the hardware), slip the ring back over the tube and tighten it onto the threads; doing so compresses the packing and makes the joint …
How should the waste pipe on a washing machine?
We always try to get the top of the waste pipe to a level which is 100mm under the worktop. If there is no worktop then the top of the waste pipe should finish at approximately 50mm down from the top of the washing machine.
What size drain is needed for a washing machine?
Drain and Trap Requirements
A 2-inch drain pipe is required for all washing machines. The former requirement of 1 1/2-inch pipe is not enough to handle the fast drainage of modern washers. As with all plumbing fixtures and appliances, a washing machine drain pipe must also contain a P-trap.
Does a washing machine drain need a vent?
All plumbing fixtures—including washing machines—must be vented. Improperly vented drains can be sluggish and noisy, and can emit hazardous fumes. Properly vented drains allow the P-trap to do its job: prevent sewer gases from escaping into your home.
How do you vent a washing machine?
Quote from the video:
Quote from Youtube video: This pipe here going down to the p-trap. Runs. I think it's roughly about 18 inches. You have to have the p-trap. Obviously. And that's important because that's going to stop sewer gases. From.
How far can P-trap be from washing machine drain?
Venting the Standpipe
The vent must rise a minimum distance from the trap that depends on the sizes of the pipes you use for the drain and the vent itself; for a 2-inch drain line, this distance is usually 5 feet.
How tall does a washing machine drain pipe need to be?
The drain plumbing needs to be at least 30″ high to be sure that no water will be sucked from it. The drain must be at least 30″ from the floor and less than 8 feet high in order to function properly.
How tall does a washer standpipe need to be?
Laundry standpipes must be tall enough to extend past the washing machine’s overflow line—typically 30-36” in height, or 18”-30” above the trap.
How far should washing machine drain hose go into standpipe?
Washing machine manuals typically specify a minimum height of 39” for the entry of the drain hose into the standpipe or faucet box, and a maximum height of 96” (8 feet).
How do you route a washing machine drain hose?
Reach around to the back of the washer with the measuring tape or yard stick. Leave the machine in its current position. Measure the maximum height of the discharge hose, at the arch, from the floor where it terminates into the standpipe in the floor, nearby laundry sink or recessed drain in the wall.
How do you position a washing machine drain hose?
Typically the hose is hung from over the side, and then over the top rim of the sink. It is important to have a sizable air gap between the end of the drain hose, and the bottom of the sink. An air gap prevents backwater from ever getting sicked back into your washing machine.
