How do you wire a light with two white and two black wires?

Take your always hot black and put it on your light switch, than take the other black in that box and put it on the light switch. Take your white that is in the same cable as your always hot black and wire nut it with your other white. Now go up to your light box.

Why does my light fixture have 2 black wires?





There are three reasons a light fixture may have two wires that aren’t color coded. The first is that it comes from a country that doesn’t follow the same electrical conventions as the United States and the second is that it is an antique. A third may be that someone converted a lamp into a hardwired fixture.

How do you connect black and white wires to a light fixture?

The black line hot connects to one side of the switch. The white neutral connects to the white of a cable going to the ceiling box. In the ceiling box the black wire is switched hot and connects to the black lead, and the white is neutral and connects to the white neutral lead of the fixture.

How do you wire a light fixture with two sets of wires?

Connect the lead wires from the fixture to the black hot wire in the electrical box by twisting a wire connector to the ends of the lead and hot wires. Repeat these connections with the two white neutral wires from the light fixture and the white neutral wire in the light fixture box.

Which wire is hot when both are black?

Here’s a rundown of electrical wires: The black wire is the “hot” wire, it carries the electricity from the breaker panel into the switch or light source. The white wire is the “neutral” wire, it takes any unused electricity and current and sends it back to the breaker panel.

Which wire is positive when both are black?





If the multi-colored wire is black and red, the black wire is the negative wire, while the red one is positive. If both wires are black but one has a white stripe, the striped wire is negative, while the plain black wire is positive. Look in the owner manual to determine which wires are negative in a car.

What to do when you have 2 black wires?

STEP 3: Identify the terminal and ground wires.



Observe the layout of the wires. You should see two black wires, each connecting to a different screw on the side of the switch. These are called terminal screws. You will also see two white (neutral) wires that connect to one another in the box.

Can you wire 2 black wires together?

This is the typical way to connect a switch. The 2 blacks connected are “power in, power out” to the next switch in the circuit. The pig-tail to the dimmer connected to the two blacks is also typical.

What happens if you connect the wrong wires on a light fixture?

But here’s the catch: If you connect the circuit wires to the wrong terminals on an outlet, the outlet will still work, but the polarity will be backward. When this happens, a lamp, for example, will have its bulb socket sleeve energized rather than the little tab inside the socket.

Which wire is hot when both are same color?



In most modern fixtures the neutral wire will be white and the hot wire is red or black. In some types of fixtures, both wires will be the same color. In this case, the neutral wire is always identified by some means. In some cases, there will be small writing on the wiring case.

How do you change a light switch with two black wires?

Connect the top screw to the wire that feeds to the light. Connect the bottom screw to the hot wire. When you turn the power back on, and if you want to swap the direction of the switch (as in press down to turn off, or turn on), turn off the power and switch the two black wires.

Why are there 2 sets of wires in one outlet?

When an outlet receptacle falls in the middle of a circuit run rather than at the end, there are generally five wires in the outlet box. Two cables are hot wires—one bringing power in, the other carrying it onward to the next receptacle. Two cables are neutral and serve the same function.

What happens if you mix up the hot and neutral wires?



This happens when the hot and neutral wires get flipped around at an outlet, or upstream from an outlet. Reversed polarity creates a potential shock hazard, but it’s usually an easy repair.

Which is live black or white?

US AC power circuit wiring color codes



See Table below. The protective ground is green or green with yellow stripe. The neutral is white, the hot (live or active) single phase wires are black , and red in the case of a second active. Three-phase lines are red, black, and blue.

How do you tell which wire is hot and which is load?

Quote from the video:
Quote from Youtube video: And then remember gold goes to the hot. Side so the gold terminal. And that's on my line. Set and then silver goes to neutral or the white wire.

How do you tell which is load and which is line?

The line side of an outlet is where you connect the incoming source power. The load side is where the power leaves the device (or electrical box) and travels down the circuit.

Is white wire a line or load?



The circuit’s hot wire (typically colored black or red) connects to the black or brass-colored screw terminal marked LINE. The white neutral wire connects to the silver-colored screw terminal marked LINE. The markings for line and load usually are printed on the back of the outlet’s plastic body.

How can you tell which wire is hot without a tester?

Quote from the video:
Quote from Youtube video: Now the wire if it gives voltage that's the hot wire. And if it does make sure you don't touch your any of these to each other or the probes to each other while you're touching them.

Does it matter what wire goes where on a light switch?

In the case of a single-pole switch, these wires are interchangeable—it doesn’t make any difference which wire is attached to which screw terminal. Inside the switch is a metal pathway that closes when the switch is in the ON position and opens to interrupt the flow of power when the switch is turned OFF.

Is the black wire the hot wire?

Hot wire is identified by its black casing. This is the main color of hot wire for most homes. However, other hot wires can red, blue, or yellow, although these colors can indicate a different function besides powering an outlet.