Can you backfeed a main panel from a sub panel?

It is not physically possible for the MAIN and the Generator to both be turned on at the same time. The only way you could have it go into the sub-panel would be if the sub-panel was interlocked to disconnect from the main panel, so you absolutely cannot feed the main from the sub, no way, no how.

How do I connect my subpanel to the main?

In the subpanel, route the feeder wires, cut and strip them, and connect to terminals. Connect the black and red wires to the hot bus bars, the neutral wire to the main neutral terminal, and the ground wire to the ground bus bar.

What wire goes from main to sub panel?

The cable you run from the main panel to the subpanel also depends on the amperage rating. You can use 10 AWG, three-conductor wire for a 30-amp panel, but for a 60-amp one, you need 6 AWG wire. If you’re installing a 100-amp panel, you need 4 AWG copper or 2 AWG aluminum three-conductor cable.

Where should feeder wires to a subpanel be connected?

Quote from the video:
Quote from Youtube video: The wire. Into the sub panel from the main panel. So we'll be running our six gauge ground wire. And our feeder wire next this is three gauge like I mentioned earlier anything six gauge or smaller.

Can I feed a main lug panel through a breaker?

Feed-Through Lugs can be used on main lug or main breaker interiors. Sub feed breakers are branch breakers mounted opposite the mains end on the end of the bussing.

Can you backfeed a generator through a dryer outlet?

Backfeeding is a dangerous and possibly illegal way to power your home by connecting your generator to an appliance outlet (like a dryer outlet) and allowing electrical power to flow in reverse. Power moves backward to your electrical panel and is redistributed throughout the house.

Does a 240v sub panel need a neutral?

A 240v only panel has no need for a neutral, I have panels in a industrial facility with no neutral, but for residential my jurisdiction requires a 4 wire feed or 3 with conduit as a ground even for all 240v loads.

Does a subpanel need to be grounded to the main panel?

Most panels come with a bar joining the two, which is easily removed. Code requires subpanels to have a ground connection that’s independent of the main panel’s.

Does a subpanel need a neutral?

The neutral and ground MUST NOT be bonded at a sub-panel. They should only be bonded at the main service panel. If you bond them anywhere other than the main service, the neutral return current now has multiple paths, including though your ground wire.

How far can subpanel be from main panel?

The right feet would be between 4.5 to 5 feet.



The cable running from your main panel to the subpanel depends on the amperage rating. For instance, for a 30A panel, use a 10 AWG, three-wire conductor.

Can you wire a subpanel with 3 wires?

Another way to wire a subpanel was with a three-wire feed; two hots and a neutral, with grounds and neutrals connected together at the subpanel. In this case, the grounds and neutrals have to be connected together.

Can a subpanel feed another sub panel?

Answer: Yes. The main electrical service panel is where branch circuits originate. A branch circuit consists of the circuit conductors between the final over-current device protecting the circuit and the lights, receptacles and equipment supplied by the branch circuit.

What is the difference between a main breaker panel and a sub panel?

A main panel is an installed box where the power from the utility company enters the premises. A subpanel is an installed features that acts as a middle ground for the main panel and other types of circuits that are connected to your property.

What’s the difference between a main breaker and a main lug?

The main circuit breaker provides a level of overcurrent protection for all branch circuits, as well as a single disconnect means for all loads being fed by the load center. Main lug only load centers are typically applied downstream of a main circuit breaker panel and are often referred to as a sub panel.

What is a convertible main breaker?

Convertible mains means that the main breaker load centers can be converted to main lugs load centers and vice versa.

How do you convert a Main lug to a main breaker?

Quote from the video:
Quote from Youtube video: You will first remove the dead front by removing the three dead front screws and sliding the dead Frank. Out. You will then remove the breaker by removing these three nuts.

What is a tandem breaker?

A tandem circuit breaker is a double circuit breaker that takes up the space of a single circuit breaker on a panelboard. You’ll also hear them called duplex, slimline, twin, half-height, half-inch, double and wafer breakers, depending on local customs.

What is a Loadcentre?

A load centre is used in residential and light commercial applications to distribute electricity supplied by the utility company throughout the home or building, feeding all the branch circuits. Each branch circuit is protected by the circuit breaker housed in the load centre.

When can you use a main lug panel?

Main lug load centers are sometimes referred to as add-on, secondary or downstream panels. These panels are added when all circuit slots in the main breaker load center are full or when a remote panel is desired.

How do you install sub feed lugs?

Quote from the video:
Quote from Youtube video: Remember to install these lugs on the end of the panel board opposite the neutral. Bar. When installing the lugs make sure to aim for the middle hole. Also remember not to over tighten the screws.