Can I put LED lights in kitchen?

Quote from the video:
Quote from Youtube video: So the idea to install LED lights was in the plans before making this installation. So what they did is they made a hole here. And they installed a receptacle inside the cabinet.

Where should LED strips go in the kitchen?





Quote from the video:
Quote from Youtube video: So i can actually run my power cord right down that gap and plug it in right behind my refrigerator. So that's going to be easy we're going to be using.

Are LED strips fragile?

Extra care needs to be taken when installing the LED strips – after all, they’re fragile components. Most issues occur by accident.

How do you hang LED lights in a kitchen?

Quote from the video:
Quote from Youtube video: And measure the length of this cabinet. And also the length of this cabinet. Here now you can install the led strip along the entire edge including underneath the microwave.

What LED light should I use in kitchen?

For kitchen color temperature, aim for either: a warm white rating between 3,000–4,000 Kelvin. a bright to cool white light between 4,000–5,000 Kelvin.

How many lumens does a kitchen need?





Kitchen: 3,000 to 4,000 lumens.

How do you hide the power cord for LED strip lights?

Quote from the video:
Quote from Youtube video: You use three-quarter inch or larger double-sided foam tape you're going to need to trim it off if you use a half-inch. It should fit right on there. And you won't need to do any trimming.

Where do LED strips go under cabinets?

If you want to install under cabinet lighting as task lighting, you should place the strip lights closer to the middle front edge of the cabinets, so the countertop will be exposed to as much light as possible. For ambient or accent lighting, you may want to place them closer to the back edge.

How do I get lights under my kitchen cabinets?

Quote from the video:
Quote from Youtube video: Space them about eight to 12 inches apart for more even lighting strips emit flooded light just choose fixtures to match the length of your cabinets rope.

How do you replace LED lights in kitchen ceiling?



Quote from the video:
Quote from Youtube video: Underneath this housing removing the old light fixture is easy just back out or loosen up the two machine screws rotate and then that will release the housing.

Can you cut LED Strip Lights?

Quote from the video:
Quote from Youtube video: Here it's important to note that LED strip must only be cut at the specified marks cutting the strip in the wrong place will result in some of the LEDs in the cut area not.

Can you hardwire LED Strip Lights?

When hardwiring the strips, you will just need to make solid connections between all your strip wires to the output wires on the power supply. This can be done with wire nuts or wiring all strips to a common positive and negative wire so you can make a one to one connection with the hardwired power supply.

How many LED strips can be connected together?



This is no different with LED strips. Vetco recommends, as a general rule, not to connect more than three complete strips end-to-end without adding in extra, higher gauge power wire or additional power supply units down the line.

Do you need a special switch for LED lights?

A standard dimmer switch cannot be used with an LED light as you will never be able to dim the LED light either completely or not very well. LED lights need their own special electronic dimmer switch to have a fully functioning and dimming light.

Can you wire LED strip lights to a wall switch?

Once you have attached your LED strip to a switch, dimmer switch, or Bluetooth wireless switch, it’s time to connect it to your power supply. You can either wire this through a wall-mounted switch or a simple switch with a barrel connector.

How do LED strips connect to power supply?

For this, all you need to do is connect the led strips to the ends of your led splitter and then plug in your female connector to the male connector on your power supply. This will ensure that power is distributed evenly and the lights are working as they should.

Can I use a dimmer switch with LED strip lights?



You can install a DC PWM dimmer between a standard, non dimmable power supply and the LED strip. It usually has a turn dial (potentiometer) that adjusts the LED strip brightness.

What power supply do I need for LED strip lights?

LED strips, unfortunately, are not as simple as traditional incandescent light bulbs when it comes to installation and set up. Because they run on low voltage DC, they require a power supply device that converts 120V/240V AC (depending on your location) into the voltage signal that LED strips can use.

How many feet of LED strip lights do I need for my room?

The first LED strip light would be much brighter than the second. LED strip lights come in a wide range of colors as well as strips that can change colors.



A Guide on How to Buy LED Strip Lights.

Use Lumens Required Per Foot
Task lighting far from source 350 to 700
Indirect lighting 375 to 575
Signs 500 to 750

How long can you run LED strip lights?

24V DC LED strip longest length is 32ft (10 metres). 24V Constant Current (CC) LED Strip is 65ft (20 meters). 120V LED Strip maximum length is 164ft (50 meters). 24V RGB & RGBW maximum run lengths are 23ft (7 metres).