How do you realign a bathtub drain?
Quote from Youtube video: And then on the top side also pull that one down we'll add a little grease in there. It's going to help it move freely. Once i've got adequate grease we'll go back down with the whole.
What is code for a tub drain?
Current plumbing codes (IPC as well as MA Plumbing Code 248 CMR 10 for instance) need 1.5 inches to drain for a tub with a shower. The tub can drain at leisure and the shower function when in utilize, with flow-limiting showerheads, fall within the flow rate that a 1.5” drain can handle.
How tight should tub drain flange be?
Do not press down on the flange. Allow the threads to pull the flange down into the drain shoe. Step 8: Use the drain-removal tool or plier handles to tighten the flange into the drain. The flange should be tight enough to prevent water leaks, but not tight enough to damage the tub.
Is tub drain a standard location?
The position of the tub drain will vary, depending on the size and design of the tub, and you’ll need to cut an access hole in the floor at the drain end of the tub to allow for positioning and installing the drain line. This hole should be 9 inches wide and extend at least 12 inches from the wall.
Why does my tub drain when I take a bath?
In most cases, an issue with the bathtub drain stopper is usually because it has disconnected from the spring or plug that connects it to the linkage. This breaks its connection to the trip lever, so the stopper cannot hold water as it should.
Should bathtub lever be up or down?
When the lever is up, the stopper is held in place, keeping your tub filled with water. When the lever is moved down, the stopper lifts and the tub drains.
How much pitch does a tub drain need?
¼ per foot
A bath tub drain shall be a minimum of 2 (horizontal) or 1 ½ (vertical) drain pipe size, with a minimum 1 1/2 vent pipe size. A lavatory requires a 1 ¼ minimum drain and vent pipe size. The minimum slope required for drainage piping less than 4 in pipe size is ¼ per foot slope.
Are all bathtub drains in the same spot?
All bathtubs drain in basically the same way, with a drain assembly located on the bottom of the tub linked to an overflow that may or may not have a toggle switch. When the plunger or stopper is opened, water drains out of the bathtub, through the drain assembly, down a tailpiece and into the trap.
Can a tub and shower share the same drain?
Yes, they will both be using the same drain pipe at somepoint inside or outside of your house. But the the pipes must join well below the level of both items or the pipe must be large enough for the combined flow, otherwise when you put water down one of them, it will flow out of the other!
How deep is a tub drain?
Thanks to the standardization, any bathtub drain can fit any standard bathtub between 14 and 26 inches in depth. The size of the drain is standardized because it needs to fit to the P-trap, which is the next component of the drain. This opening also has a standard size of 1.5 inches.
Are tub drains universal?
Bathtub drains are 1 1/2 inches wide and fit all standard bathtubs ranging from 14 to 26 inches deep.
Are bathtub drains standard size?
Down the Drain
According to Bonnets Stems and Accessories, Inc., a standard modern bathtub drain is 1 1/2 inches in diameter – the width straight across the middle. Rough-in plumbing should be calculated for a 1 1/2-inch pipe.
Can I use 1.5 inch pipe for shower drain?
A 1 ½ pipe can be used for shower drain in some areas. It is effective for draining water in small bathtub areas but may overflow the shower base if the water flow is high. Though a 1 ½ pipe is not as efficient as a 2 inches shower drain pipe, it would suffice in small areas.
Do you need a trap on a bathtub drain?
Does a bathtub need a P-Trap? Yes, you should always install a P-Trap as part of the plumbing of a bathtub or any other wastewater drain system. Failure to include a P-Trap could result in foul smells, harmful gases, and small animals entering through your tub’s drain.
Why does a shower require a 2 inch drain?
A 2-inch pipe is the recommended size because showers have a low threshold for flooding, and a 2-inch pipe helps the water drain faster than does a 1 1/2-inch pipe. So, if you are converting from a tub and shower combination to a shower, you’ll likely have to change the drain pipe size.
Does a shower drain need a P-trap?
P-traps, the curving section of pipe you can see under the sinks in your house, perform a vital function for any plumbing fixture in a building. Shower and bathtub drain pipes must incorporate a P-trap; otherwise the health and safety of anyone in the building will be jeopardized by sewer gases entering the building.
How high should a shower drain be from the floor?
Make sure your drain pipe is at the appropriate height (approximately 1/4 inch above your concrete or subfloor).
What is code for shower drain size?
While a shower usually requires a 2-inch drain pipe, the vent pipe must be either 1 1/2 inches or 2 inches depending on local requirements. Be sure to double check this to see what the code is in your area.
How much slope does a shower drain need?
To efficiently drain, the recommended minimum slope for a shower floor is about 4 percent, or a 1/2 inch drop per every 12 inches from the shower walls to the drain. In traditional tile shower construction, this slope is established in the mortar pre-pan.
How far can P-trap be from shower drain?
The maximum distance between the shower drain and the P-trap is 5 feet. However, the P-trap should be as close to the shower drain inlet as possible. You should even have the P-trap directly under the shower drain for the best results.
