Yes, it’s a good idea (see answer below). Based on your picture, it’s a older house so there is likely a 4″ stud that you’ll need to drill through so be ready for that and be ready for nails.
Can you drill through door header?
Yes you are fine. A hole can be up to 1/3 of the width meaning you are good for about 3″. I would try to center them and space them out if you go the full 2″. Also whenever I drill larger holes in joists I like to add a crosser right in the area going perpendicular from that joist to the next.
How do you run a cable through a doorway?
Quote from the video:
Quote from Youtube video: Bye-bye welcome to the video of the day our video surprise is actually a cable safe protector for wires and cables. We can loop it around the doorway in this brand off length.
Is it OK to drill holes in studs for wiring?
Most electricians keep their inspector happy by drilling 3/4-in. holes dead center on a 3-1/2 in. wide stud. This gives them a hole large enough to run two electrical cables and leave 1-3/8 in.
Can you drill into metal door frame?
In general, it’s a good idea to drill through metal using as slow a speed as possible using a drill bit for metal. Hard metals like steel and larger drill bits require even slower speeds. With a small twist bit (1/16 in. to 3/16 in.), you can drill through most metals at 3,000 rpm.
Can you run wires above a door?
If you have a framed doorway and baseboards along the walls, you can run wires or cables to any point along the edge of the room. That way, the setup is both safe and out of sight, allowing you to enjoy your living space without worries or distractions.
How do I run a wire through a header?
Wrap the end of a piece of wire with duct tape. Push the wire through one wall opening, and out of the second wall opening. Attach the power wire to the stiff pulling wire with the duct tape. Pull both wires back through both holes to run the wire along the path you need.
Can you screw into a door frame?
Properly installed, at least some of the screws should go thru frame and into studs. The short screws are mostly there to keep everything aligned while a pre-hung door-and-frame set is assembled and shipped. Once it has been hung and shimmed properly, those screws can be replaced with better ones… but aren’t always.
How do you drill through a door frame?
Quote from the video:
Quote from Youtube video: And we bolt the hole saw on to the end of it. Here. This is the two and 1/8 inch hole. Saw so once that's cranked down we stick it in and drill and make a big hole in the door.
How do you screw into a wood door frame?
Quote from the video:
Quote from Youtube video: So you want your framing to be a little bit snug. So you have to gently tap it into place but you don't want it to be so much that it pushes things out of square or out of level.
Can you run wire behind baseboard?
To avoid the difficult and costly work involved in repairing walls and matching texture and paint, one way to run a cable in a wall is behind the baseboard. The patchwork will be concealed behind the baseboard and will not require a drywall expert to make a beautiful finished product.
Where do you staple electrical wires?
Quote from the video:
Quote from Youtube video: First you want to make sure your wire is flat when you staple it down not on its side you also want to staple as close to the center of the stud.
Can you drill through a header joist?
The hole cannot be larger than one-third the depth of the joist, so the maximum hole size for a 2×12 joist (actual size 1-1/2 x 11-1/4 in.) is 3-3/4 in. diameter—plenty big enough for running cable! You can drill the holes anywhere along the length of the joist (first photo).
Can you drill through a load bearing beam?
Structural Beams / Load Bearing Support Beams:
This is a structural support beam which is load-bearing. Do not drill through these!
Can you drill into door?
To drill the hole, first locate where you want it with a pencil. Then use a center punch with a hammer to tap a small indent right where you want the hole. If you don’t have a center punch use a nail. If you don’t tap a center mark, your drill will skate right across the surface of the door and scratch the paint.
How do you screw into a metal door frame?
Quote from the video:
Quote from Youtube video: Can't move around to use it just place the end of the punch on your mark. And hit it with a hammer. Now you have a little indentation. Once it's punched you can use it just like any ordinary screw.
How do you drill through a door frame?
Quote from the video:
Quote from Youtube video: And we bolt the hole saw on to the end of it. Here. This is the two and 1/8 inch hole. Saw so once that's cranked down we stick it in and drill and make a big hole in the door.
How do you screw into a door frame?
Quote from the video:
Quote from Youtube video: There. First thing i want to do is pre-drill. A hole got it okay now i want to check the jamb to see if it's plumb right on the money. Now i can finish screwing off the hinge.
How do you cut a door frame for electric strike?
Quote from the video:
Quote from Youtube video: And then we're going to use a plunge cut tool or a fine cut tool flush cut tool whatever you want to refer to it as this is a 18 volt plunge cut tool from milwaukee.
How much weight can a hollow door hold?
In this article, I will share the principles needed to determine how much weight your door can hold. In general, an interior door in a residential house can hold between 45 to 100 pounds. An exterior door with robust hardware can withstand anywhere from 200 to 400 pounds.
