How do you combine two wires?

Quote from the video:
Quote from Youtube video: You're going to press them into the connector as shown. And then when you insert the second wire you're actually going to push that wire into the other.

What do you do with extra wires in a light fixture?

Quote from the video:
Quote from Youtube video: For this job you will need some wire nuts and electrical tape so here's a standard electrical box this sits in between two studs.

Can you splice light fixture wire?

Adding a Light Fixture Mid-Circuit

If the cable is too short, you may have to splice on a short length of extra wire. The splice connections must be inside a separate covered electric box attached to the framing. The code requires the box to be in an accessible location so you can get to the wires if needed.

How do you splice a lighting cable?


  1. Remove Outer Sheathing From Cable. Make sure that you are joining two similar cables. …
  2. Strip Insulation From Conductors. …
  3. Inspect the Cables. …
  4. Remove Knockouts From Junction Box. …
  5. Attach Cable Clamps to the Junction Box. …
  6. Insert the Cables. …
  7. Attach the Box and Cover Plate. …
  8. Make the Wire Connections.

How do you join wires without soldering?

Quote from the video:
Quote from Youtube video: Use the uninsulated area which is the bottom and crimp down as hard as you can. Now this crimp works pretty good. It takes a little bit of force to remove this connector.

How do you tap into a wire without cutting it?

Quote from the video:
Quote from Youtube video: And slice the jacket open our goal here is to expose about three-quarters of an inch to an inch of the wire strands inside the jacket without cutting through the wire.

How do you wire a light fixture with two sets of wires?

Connect the lead wires from the fixture to the black hot wire in the electrical box by twisting a wire connector to the ends of the lead and hot wires. Repeat these connections with the two white neutral wires from the light fixture and the white neutral wire in the light fixture box.

Why are there so many wires in my light fitting?

The UK ceiling rose is standard – it is normally┬╣ the place where wiring is connected to and from other nearby lights (including those in other rooms). That is why there are more wires than you might expect.

What are the two black wires in my light fixture?

If you end up with a fixture with two black wires, you can examine the texture first. Some fixtures with black wires have one smooth wire and one that has a ribbed texture. If this is the case, the ribbed wire is neutral and connects to the white wire in the ceiling.

Can you extend electrical wire?

Quote from the video:
Quote from Youtube video: If there's not enough wire left to do that then straighten out the old loops prepare three 6-inch jumpers then grab the old wire and push the bare end into the push in connector.

How do you extend a ceiling light wire?

Quote from the video:
Quote from Youtube video: Coming through the front you can see it's pushed in through the back. Slide it up mount it into the ceiling opening. Now. Make sure that your wires are extended.

How can I make my light fixture longer?

Buy a chain or a downrod and cut it to the desired length. Purchase chains and downrods at any hardware store, and most stores will cut them for you. Purchase the same type of hanging material currently used by your fixture. If your fixture currently hangs by a chain, buy a chain of the same or greater thickness.

Can you splice wires without a junction box?

Short answer: NO. Long answer: All splices must be in a junction box, and the junction box must be accessible.

Is it OK to use a junction box to extend wiring?

Mistake: No electrical box | Never connect wires outside of electrical boxes. Junction boxes (or a J box) protect the connections from accidental damage and contain sparks and heat from a loose connection or short circuit.

How do you install a junction box on a light fixture?

Quote from the video:
Quote from Youtube video: Once you have the wire in the box you're going to push. The box back into the ceiling. And the box will have this particular one has three clips. So as you screw. The screws in the clips.

Are electrical junction boxes legal?

Yes any concealed box is a code violation. All splices must be accessable. Now practically speaking if the splice is made properly with wire nuts and the cables properly clamped in the box, you can cover it without concern.

What is a junction box for lighting?

The modern lighting junction box, or electrical box, is where the electrical wires originate. The junction box is where you will connect the wires to the cord set, and also where the ceiling canopy will attach to support the light fixture.

Can you install a light without a junction box?

Common examples of electrical devices that require no junction boxes include: Recessed lights (“can lights”) Bathroom ventilation fans. Wall-mounted heaters.

How do you install a floodlight without a junction box?

Quote from the video:
Quote from Youtube video: So you can run conduit. And it's got one in the back. It comes with a little four screw caps you put those in makes it a good solid.