Should access point be mounted on ceiling?
Placing AP’s on the Walls
Some manufacturers say access points can be deployed both on the wall and on the ceiling, but this typically isn’t the case without sacrificing some performance. From what we’ve seen, placing AP’s on the ceiling provides the best experience to your users.
How do you hang something heavy on a plaster ceiling?
Screws (and screws with masonry anchors for heavy items) are your best choice for hanging things on plaster walls without picture rail. For lighter items, simply screwing into the plaster with a 1 1/4” drywall screw is usually enough to get the job done.
How do you install a ceiling access point?
Quote from the video:
Quote from Youtube video: It's kind of in the center of the house. And that's where you want it. In the ceiling you can also install it on a wall like we could put it right here on the wall.
Can you have too many wireless access points?
Although common sense may suggest “more is better,” too many wireless access points (APs) quickly leads to excessive radio frequency (RF) broadcasting as well as wasted resources on unused APs. Consider the requirements of the space and expected number of connected devices.
Should I mount my router on the ceiling?
Consider even mounting the router on a wall or in a corner by the ceiling if you have two floors because radio waves generally spread out and towards the ground, not up. Think about putting your router on the second floor if you have one.
How much weight can a plaster and lath wall hold?
They can generally support pictures of up to 20 pounds. As mentioned earlier, avoid using nails on plaster wall because they will likely cause the drywall to crack. Instead, use a screw, because they won’t break the plaster wall.
How do you anchor a plaster ceiling?
Quote from the video:
Quote from Youtube video: And after you pop out the other side on the inside of the wall. It flares back out and then when you tighten it it grabs a hold of a bigger portion of the drywall or plaster.
How do you hang things on lath and plaster walls?
Drywall anchors can be used on plaster walls the same way they’d be used on drywall. However, in many cases, they’re not necessary, because it’s easier to get a screw into the lath. I only use drywall anchors on plaster walls when I’ve gotten other screws into the lath or a stud, and I’m hanging a large piece.
Can a router and access point have the same SSID?
In most cases it is. Two different routers (not mesh routers) with the same SSID works fine. But if you connect to A and walk to B, it may remain connected to A unless signal for A drops off forcing connection to B. You may have to do this for best connection where you are.
How far apart should wireless access points be placed?
Distance between two APs should be approximately 30 to 70 feet.
Is mesh WIFI better than access point?
And if you can run an Ethernet cable all of the way to where you need it, you’ll be even better off than going with a wireless mesh routing system. Access points extend a network in an affordable way and it’s the best solution if you only need to fix one area of your home or building that struggles with Wi-Fi.
Can access points be too close together?
Nothing wrong with this as long as the access points use non-overlapping channels. If the channels do overlap it could cause a situation where their access points interfere with each other. This can cause packet loss during browsing and a negative internet experience for those using your WiFi network.
Why are access points more expensive than routers?
The wireless access point will cost more than a wireless router because there is more coverage. If your business requires multi-AP interconnection, that will raise the price as well. However, the price is worth it for reliable and consistent Internet access.
Does access point need to be wired?
A Wireless Access Point (WAP) allows several devices to connect via WiFi to a single network. The wired equivalent is a switch. But unlike a switch, a WAP does not need to be wired to the router. Access Points connect via wired Ethernet to a switch, or a switch port on a router, then serve up WiFi.
What IP address should I use for access point?
The default IP address of the Access Point or Range Extender is 192.168. 1.1 or 192.168. 1.254 or 192.168.
Is access point better than repeater?
An access point is better for adding multiple wireless networks. For segmenting existing networks such as visitor or guest networks while keeping your internal network secure. An access point can also connect to a switch which can be useful for buildings without routers.
What is the difference between wireless router mode and access point mode?
Best answer: The difference between router mode and access point (AP) mode is that router mode handles your home network’s creation and deals with internet traffic. AP mode allows you to extend the reach of your wireless signal by acting as a relay with a few simple software changes.
How does Wi-Fi access point work?
Access points work by connecting direct to your broadband router or network switch with a Ethernet or data cable. This provides the AP with the internet connection and bandwidth required. It then transmits and receives a wireless signal in either the 2.4Ghz or 5Ghz frequency range (WIFI).
Should I use AP mode or bridge mode?
An access point links an Ethernet-only device or multiple devices with your wireless internet network. Go for a router bridge if your primary concern is sharing data between two separate networks. Choose AP mode if you want to connect Ethernet-only devices to Wi-Fi.
