https://youtu.be/CsNOCZTYcz4
How do you fill a deep hole in concrete floor?
How to fill a Large Hole with Concrete
- Step 1: Use a hammer and a cold chisel to level the bottom of the hole. …
- Step 2: Brush on a concrete bonding liquid. …
- Step 3: While the bonding agent is still tacky, mix the concrete. …
- Step 4: Level the patch.
What can I use to patch holes in concrete floor?
Pack a Small Amount of Anchoring Cement into the Hole
Smooth the surface with a putty knife or trowel. Anchoring cement expands as it hardens. It is primarily used for anchoring bolts in holes drilled in concrete, but it also works well here. Keep the area moist until the patch cures.
How do you patch a large hole in a concrete floor?
Shape the hole in the concrete floor into a square with a hammer and chisel. Keep the bottom of the hole uniformly level and chisel the four sides of the square so they are undercut slightly. This is a technique where the hole is wider at the bottom than at the top so that the concrete patch adheres firmly.
How do you attach a bottom plate to a concrete floor?
Quote from the video:
Quote from Youtube video: So what I did was I use these things called sleeve anchors a brand called red head and the way these work is you drill a hole through the stud and the concrete.
What is best to patch concrete?
The Best Concrete Patches of 2022
- Best Vinyl. Damtite 04012 Gray Bonds-On Vinyl Concrete Patch.
- Best Overall. Red Devil 0644 Pre-Mixed Concrete Patch.
- Runner-up. Damtite 04072 Concrete Super Patch Repair.
- Best Bang for the Buck. Quikrete #862013 5.5 Oz Concrete Repair.
- Best for Floors. …
- Best for Walls. …
- Best Acrylic. …
- Best Vinyl.
How do you fill a large hole in the floor?
Quote from the video:
Quote from Youtube video: So now all you have to do is cut this out and away you go cut out a piece of wood to fit in underneath here you might call it sub sub before. And I drilled a few holes in it here.
Does concrete bonding agent work?
The use of a bonding agent helps the different concrete layers to behave like a single unit, thus increasing the strength and performance of the structure. The bonding agent is applied over the existing surface of the concrete so that the new layer of fresh concrete successfully adheres to the old layer.
What is epoxy concrete repair?
Concrete repair epoxy is a method whereby epoxy is combined with cement when making repairs. The cement is then made stronger and will also be stain-proof. When adhering to instructions and following the correct process for repairs, in the end, it will save you a lot of time and money.
How do you fill large gaps in concrete?
Quote from the video:
Quote from Youtube video: Some. General purpose sand.
How do you attach framing to a basement floor?
Quote from the video:
Quote from Youtube video: Then I have this impact driver which I use to secure these tapcon screws into place. So these tapcon screws are basically what I use to attach these basement frames to the floor to the concrete.
What is the difference between a sole plate and a sill plate?
The sole plate, also sometimes referred to as the sill plate, the mud sill, or the base plate, is the main supporting beam of a wall in the construction industry. Typically, these are the first piece of wood that is in contact with the masonry of the basement or foundation.
How do you seal a sill plate to concrete?
Air seal between the sill plate and the sub-floor with caulk, foam, or an equivalent material. Install a foam gasket beneath sill plates that are sitting on concrete or masonry and adjacent to conditioned space to both air seal and serve as a capillary break between the concrete and the sill plate.
How do you seal between foundation and framing?
Quote from the video:
Quote from Youtube video: Let me show you how easy it is to use a fluid applied flashing for this situation. And oh by the way it's sprinkling. And this fluid applied flashing. It actually cures with moisture.
How do you fill gap between sill plate and foundation?
use simple planks to make shuttering/formwork (top level of future concrete will be like 1-3mm above the bottom of foil under the sill plate) wrap bottom side of sill plate with some kind of continuous foil (water/moisture insulation) lay the self-levelling concrete, be sure that the concrete fills all the space.
What goes between sill plate and foundation?
For additional moisture protection, a gasket or strip of closed-cell foam can be installed between the concrete foundation and the sill plate.
What should I put between 2×4 and concrete?
Quote from the video:
Quote from Youtube video: Makes a tape called wig love and this is a particularly good choice wherever we're sticking to concrete. This is going to stick without a primer although certainly we could use a primer.
How do you seal a gap between concrete and wood?
How to Water Proof Between Wood & Cement
- Load a tube of caulk into a caulking gun. …
- Cut the end of the caulk tube off with a utility knife to accommodate the size of the gap between the wood and the cement. …
- Fill the gap between the wood and the cement with backer rod if needed.
What does a sill plate look like?
Quote from the video:
Quote from Youtube video: And today I'd like to talk a little bit about foundation sill plates this is the piece of wood that is the first piece of lumber that's typically put on top of a masonry foundation.
How do you replace a sill plate on a concrete slab?
Quote from the video:
Quote from Youtube video: By your local building authorities. And that would simply be to cut a notch in the bottom plate. And then slide it underneath the wall framing studs.
Can a sill plate be replaced?
The thing about removing a sill plate is that you have to support all the weight above it while you remove and replace it.
