How do you shingle roof corners?
How to Shingle a Roof (90 pics, Pro tips, Recommendations)
- Step 1: Remove Existing Roof and Underlayment. …
- Step 2: Remove Roof Sheathing. …
- Step 3: Install New Sheathing. …
- Step 4: Install Drip Edge. …
- Step 5: Lay Leak Barrier Underlayment. …
- Step 6: Lay Felt Paper Underlayment. …
- Step 7: Snap Chalk Line. …
- Step 8: Begin Starter Course.
Do you overlap shingles side by side?
Using your cap nails, secure the deck protection to the roof. Overlap each row at least 3 to 4 inches. If you live in an area with inclement weather, you should consider using a special leak barrier protector.
How do you lay shingles for beginners?
Quote from the video:
Quote from Youtube video: First thing you're gonna want to do is take a full shingle. And you're gonna go flush. Along the eave starter. And flush along the rake starter.
How do you stagger architectural shingles?
Quote from the video:
Quote from Youtube video: Start the second course with a shingle from which 8 inches has been cut position the remaining portion over the first and align the bottom edge. Along a line level with the saw to the overlay leaving
Should shingles overhang drip edge?
The edge of the shingles should hang over a roof between an inch and an inch and a half — or between a half inch and three-quarters of an inch if drip edge flashing is installed. Too much overhang and the shingles could blow off in high winds; too little can allow water to seep into rake or fascia boards.
Should drip edge be tight to fascia?
A vertical drip edge lip extends down roughly 1 5/8″ and as Steve points out, should not be set tight against the fascia board or water may run behind the gutter and down the fascia, inviting leaks and rot.
How do you layout a shingle roof?
Quote from the video:
Quote from Youtube video: If you're hanging your shingles over which we don't do here in South Florida. We don't hang them over we have drip edge that that has a little edge on it and we lay it flush mostly due to high wind.
Do shingles go over or under flashing?
Instead of installing the step flashing between shingles, the flashing rests on top of the shingles. It’s not unusual to see sealant installed when sidewall flashing is missing. Sealant will eventually dry, shrink and crack. You’ll see sealant substituted for flashing in a lot of different areas on roofs.
Does fascia go on before shingles?
If your roofers are replacing your fascia board as part of a full roof replacement, then they will install the new shingles before they address the fascia. There is no way to replace the fascia board without removing the gutters, as the gutters are mounted to the board.
How far should shingles be staggered?
six to 15 inches
With laminated shingles, the stagger ranges from six to 15 inches, depending on the type of shingle and the shingle manufacturer’s instructions. In a few cases, manufacturers may allow four inches, but that is not common.
Should shingles be staggered?
Call it whatever you want, you should be looking at roof shingle stagger. Stagger is important because, if the spacing is less than 4 inches, water can travel from joint to joint under the shingles and create a leak in the roof.
How much should architectural shingles overlap?
Overlap each row by two inches. Sides should be overlapped by four inches. Use a bare minimum of fasteners; just enough to hold the underlayment in place for the next step. Make sure that you apply one layer of underlayment over the metal drip edge along the eaves.
How far should shingles stick out past the drip edge?
3/4”
Shingles should not extend more than 3/4” (19 mm) past the drip edge. If shingles overhang the edge of the roof by more than 3/4” (19 mm), then they are not supported and may crack and break off. In addition, the wind resistance at the roof edge may be compromised.
How far should shingles extend over gutter?
1/4 to 3/8 inch
Most shingle manufacturers recommend a 1/4 to 3/8 inch overhang over your eave, which is where your roof ends by your gutter. In many cases, and particularly as the home ages and settles, the roof edge at the eave edge can wave in and out by more than this amount.
Does drip edge go all the way around the roof?
Drip edge is installed around the whole perimeter of the roof. It is used to hold the underlayments down and create a watertight seal around the edge of the roof. Only the face of the metal is seen and is usually just white one to one and half inch stripe located right under the shingles and above the fascia.
How do you corner a drip edge?
Quote from the video:
Quote from Youtube video: So to put a 90 degree corner on your drip edge it's as simple. As taking the top of the profile. And cutting a straight line. And then you're going to come to the front of your profile.
Should tar paper go over drip edge?
Installing roof drip edge flashing properly
The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge. This lets any water that gets on the roof run down the underlayment and over the drip edge.
Does ice and water Shield go under drip edge?
Ice and water protector needs to be installed directly onto the roof deck after you have placed the drip edge at the eave. (The drip edge will be installed over the ice and water protector and other underlayments at roof rake edges.)
Does roofing felt go over or under drip edge?
At the side, or gabels, of a roof, the drip edge goes over the roofing felt. At the bottom of the roof, the drip edge goes under the roofing felt.
Do you need tar paper over ice and water shield?
Ice and water shield need to be installed before other underlayments, including roofing felt. Tar paper compared to ice and water shield do not stick to anything, whereas ice and water shields are a rubberized membrane that is very sticky to create a waterproof barrier to standing water if installed correctly.
