How do you flash a ledger board for a pergola?
How to Flash a Ledger Board for a Pergola
- Loosen any siding that is in place along the wall above the ledger board, if necessary. …
- Squeeze silicone adhesive onto the top edge of the ledger board along its length. …
- Reattach the siding on top of the ledger board, locking the Z-flashing in place.
Where do you put the ledger board on a patio cover?
A ledger should be affixed to strong parts of the house’s framing, such as second-floor joists or wall studs. The strongest ledger connection relies on bolts that run through the ledger and the house sheathing and rim or band joist and then are fastened with nuts and washers affixed from the other side.
How do you attach a ledger board to a patio?
Quote from the video:
Quote from Youtube video: And I just want it to be nice and sturdy I use them to buy 10 here for my fate for my ledger board and all the rest of my deck framing boards as well. And gonna use a six by six post. Two concrete
Does a deck ledger board need flashing?
Quote from the video:
Quote from Youtube video: So let's go over some of the components of this little demo here of the deck ledger flashing. And then we'll talk about the flashing. Itself. So this is the port concrete foundation on some grass.
How do you attach a pergola to a roof?
Quote from the video:
Quote from Youtube video: To get started we need to locate the top wall. Plate. Our next step is to carefully remove the shingles to expose the wood underneath. It's really not as hard as you might think.
Can you attach ledger board to fascia?
If you own a two-story home, you can tie the ledger into a band joist. Find the band joist by measuring down from the 2nd story window. When you attach the ledger boards to the fascia, they should be held securely with bolts through the wall, or you can use lag screws.
How do I secure my patio pergola?
Quote from the video:
Quote from Youtube video: With a ledger in place we move on to installing two posts that will support the other end of the structure. The bottoms of these posts will be held in place by these post brackets.
How do you waterproof a pergola roof?
Quote from the video:
Quote from Youtube video: These are about 23 and a half on center so that's what we spaced our rafters. At so we cut down the first one to that measurement we'll get this up this will be splitting right on our first rafter.
Can you rest a pergola on a roof?
For most pergolas, two SkyLift Roof Risers are all that are needed to support the structure on the house side. Saddles on top of the Roof Risers are made to fit either a 4-inch or 6-inch beam that the pergola structure sits on and attaches to. The free side of the pergola sits on a similar beam supported by posts.
How high can you build a pergola without planning permission?
height must be no greater than 2.5m (8′ 2″). Further away from the boundary it can be 3m (9′ 10″). A pitched-roof structure (A-shaped roof) can be up to 4m high (13′). It mustn’t cover more than half of the area of your land.
What kind of roof should I use for a pergola?
Vinyl or plastic will look great at first, but will eventually fade and distort. Metal louvers, like aluminum, are the ideal material for a pergola roof. Aluminum is strong and lightweight, making it possible to automate their controls with quiet electric motors.
Can I attach pergola to fascia?
The Alumawood Pergola Lattice covers attach directly to your homes fascia board, fascia board does need to be at least two inches thick, the rafters are available in two heights, 6 1/2″ and 8″, most kits are 6 1/2″ and you need to verify there is enough room for the rafters to attach to your fascia board.
How do you attach a patio roof to fascia?
Quote from the video:
Quote from Youtube video: The back channel and fascia is then strengthened by reinforcing two rafters. Inside the roof the patio sheets are then fixed and supported inside this channel which has a seal.
Should a pergola be attached to house?
Pergolas attached to a home (or other outdoor building) are more structurally secure than freestanding ones. They share the stability of the structure, which also provides added protection against the elements. For this reason, permitting is typically required for attached designs.
