How do you fix a gas stove burner that won’t stay lit?

Quote from the video:
And you can use a flashlight to see what you're doing and then wiggle it around maybe five or six times to break up whatever the residue is. And once that's done put the cap back on.

Why does my gas burner not stay on?

The most common cause of this is dirty or blocked burners, which is the part that you can easily take off to clean. All the small holes on the burner should be clean and clear, if not then even a partial blockage can lead to the thermocouple not getting enough heat and, the burner won’t stay lit.

Why does one of my gas burners won’t light?

Whether it’s grease buildup or food crumbs, one of the most common causes for a gas burner that has trouble igniting is debris blocking gas flow to the igniter. The fix: Begin by removing the grate covering the troubled burner. Next, remove the burner cap, which should lift off with ease.

How do you clean a thermocouple on a gas hob?

Quote from the video:
So take off the bracket that secures it in this case paper to put a little bit of wd-40 on it to get it thrown lift it. Up.

Why are the burners on my gas stove slow to light?

Gas surface burners are often slow to light or will not light at all because the burner or burners are wet or dirty, the electrode is not seated properly or the burner head and cap are not matched up properly.

How do I get my gas hob to stay on?


  1. Push the control knob down and turn it counterclockwise to the maximum position, don’t try to ignite the burner on a minimum position.
  2. After you have lit the flame, keep the knob pushed for equal or less than 10 seconds.

What is a thermocouple on a gas stove?

The thermocouple, which operates as a safety device, turns the gas supply off when the pilot light goes out. It consists of a heat sensor connected to a solenoid; when the sensor is not heated by the pilot flame, the solenoid closes the gas supply line. When a thermocouple fails, the pilot light won’t stay lighted.

What happens if a thermocouple fails?

Normally when the thermocouple malfunctions or isn’t working, it simply shuts off the gas to your heater. This is important, particularly if the pilot light is out, because it prevents harmful gas from leaking into your home.

How much does it cost to replace a thermocouple UK?

Although a replacement thermocouple is an inexpensive part, the cost for a boiler engineer to fit it is likely to bring your boiler’s thermocouple replacement to approximately £150.

Where is the thermocouple on a gas stove?

Trace the copper tube into the oven body. The thermocouple head is at the end. The head is affixed near a burner with either a gravity clip or a clip that has been screwed into place.

How long does a thermocouple last?

Thermocouples can last up to 10 years if properly installed and maintained, while furnaces can last 15-20 years, although either may wear out sooner in multifamily units.

How do you troubleshoot a thermocouple?

Quote from the video:
Now if your thermocouple was originally grounded and now you're getting a Noel that means that the junction has somewhat come apart from the sheath of the probe.

How do you clean a thermocouple?

Yes, you can clean a thermocouple, but the task must be done with a light touch. Remove the thermocouple from the process assembly, using a steel wool or emery cloth, lightly clean the tip removing any build up. Cleaning a thermocouple is not a fix for an issue, such as inaccurate readings.

How much is a thermocouple?

1 cause of pilot lights that won’t stay lit is a worn-out thermocouple. It’s easy to replace and a new one costs $5 to $10. Rather than trying to unfasten the thermocouple inside the water heater’s burning chamber, it’s easier to remove the whole burner and thermocouple assembly.

How do you clean a thermocouple pilot light?

How to Clean a Pilot Light

  1. Cut off the gas to your furnace. …
  2. Remove the pilot light and thermocouple assembly. …
  3. Use your pliers or wrench to remove the pilot light and thermocouple from the bracket.
  4. Using the wire brush, brush away the carbon buildup and soot from both components.