How high off carpet should door be?

The gap at the bottom of an interior door should be 2 inches from an unfinished floor. Over a finished floor, the gap should be between ¾ to ½ of an inch, depending on the type of floor you have. The gap at the bottom of an exterior door should be almost nonexistent.

Do you hang doors before or after carpet?





The standard procedure is to install carpet after the doors and trim are installed. If you were installing vinyl or tile, you would do the same, but hold off on any quarter round trim until you’re done. The important consideration, particularly for pre-hung doors, is how high to install it above the subfloor.

How high should door trim be from floor?

The term trim includes door casings, baseboards, and any molding that will come in contact with the floor. They should be kept 3/8″ to 1″ above the floor if installed before the carpet is laid or according to the manufacturer’s instructions.

Do you have to take doors off to lay carpet?

Some installers will remove doors in order to install the carpet and re-hang them if possible. They probably won’t shave or cut down doors to insure clearance.

Should carpet touch the door?

Bottom line is try to minimize the amount of contact between the door and carpet by trimming the door so it just contacts the top of the pile and you should be fine. It also depends on how often you open/close the door. If it’s a door that is rarely moved, then it will not matter much.

How much should I cut off the bottom of a door for carpet?





Typically you only need to trim 1/2 inch from the bottom of the door. If that’s not enough, you can trim off up to 3/4 inch. Hollow-core doors, which are the most common for interior usage, are built around a frame on the outside perimeter. If you cut too much off the frame, the door will can separate.

What comes first interior doors or flooring?

I’d vote for doors first, it will make installation of the door easier by not having to worry about floor clearances. Once installed, when you’re doing the floor, you then cut the jamb legs so that they just clear the flooring and any padding, glue, etc. that may be installed along with it.

How do you install a Prehung door on a carpet?

Here are the steps you need to follow.

  1. Remove the old door. The first step is to remove the old door. …
  2. Measure the rough opening. …
  3. Check that the floor is level. …
  4. Adjust the jamb according to the measurement you took. …
  5. Place the door in the rough opening and line it up. …
  6. Close the door and check the installation. …
  7. Fit the trim.


What goes first flooring or doors?



Hardwood flooring goes first. Wheni install prehung doors, the jambs and door are crefully fitted to the final rough opening which includes the finished floor.

How do you rehang a door after carpeting?

Quote from the video:
Quote from Youtube video: Bring your door out and set it up on top of something you want to cut off the bottom and never cut off the top of the door I always cut it off from the bottom.

How do you tuck carpet under a door?

Quote from the video:
Quote from Youtube video: Over lapping the edge of the Z bar there cut it about a half inch hefty. That way you got enough to work under.

Where do you stop carpet in doorways?



To Summarize



When installing carpet, it should end in the center of the doorway. This way, the transition from one floor to another remains hidden when the door is shut. The two kinds of flooring meet under the closed door, and only one floor is visible from any direction.

How much of a gap should be between door and floor?

The most common method of figuring out the height for the top of ALL the doors is to make the bottom of the door blank 1 & 3/4″ off the subfloor which should be consistent throughout the house (unlike the heights of finished floors). This leaves a 1″ gap for solid 3/4 hardwood floors.

What is the space between the door and the floor called?

The door sill is the very bottom part of the door frame that rests on the floor.

How much gap do you leave in carpet?

3/8″ is a safe, standard gap. If you’re using common 3-1/4″ or 3-3/4″ base trim, use a few scraps of that. It may be 7/16″ thick, but that’s fine also. Having a gap allows an extra measure of prevention against gaps in case the carpet shifts at all, and certainly makes life easier for the carpet installer.

How do you fill gaps between carpet and walls?



To seal the gap between the wall and carpet, you must use one of the four options below:

  1. Silicone caulk.
  2. Expanding foam.
  3. Shoe molding or quarter round molding.
  4. Adjust the baseboards (or replace them if needed)


Do you need baseboards with carpet?

Generally, the installation of carpet or baseboard is easier for whoever installs first. Some professionals may have a strong preference, but ultimately baseboards can be installed before or after carpet. Ask your carpet installer their preference to begin the discussion.

Should there be a gap between baseboard and floor?

If the gap between your baseboard and tile floor is ¼-inch or smaller, it should be filled with caulk. If the gap is larger than this, it’s best to install shoe molding to hide the gap. When caulking gaps between your floor and tile, it’s essential to use a paintable caulk.

What can I use instead of baseboards?



Ranging from “why didn’t I think of that” to totally out-there, here are thirteen alternatives to wooden baseboards.

  • Before You Forego Baseboards. …
  • Tile. …
  • Peel-and-Stick Decals. …
  • Reglet Trim. …
  • Flush Base. …
  • Shiplap. …
  • Molding. …
  • Recessed Lighting.