Should a shower tray flex?
If your shower base and drain fitting have been correctly installed, minor flexing will likely cause no problem at all. The flexing may be completely within the expected performance of the shower pan.
Should a shower tray be level?
Step 5 – Use a spirit level to ensure that the tray is completely level the whole way around. This is one of the most important steps in installing a shower tray as a tray that isn’t level will cause issues with drainage and water could gather on one side of the tray and potentially overflow.
What do you stick a shower tray down with?
Using either tile adhesive, silicone or a weak cement mix (5 parts sand/ 1 part cement) apply sufficient to board to cover entire underside of tray.
How much weight can a shower base hold?
A cement or mortar shower base can easily hold upwards of 1,000 lbs, but the exact amount of weight a shower base can hold is dependent on a few factors: Residential floors built to code can support very heavy objects, but old or damaged subflooring may be weak.
Why is my shower floor soft?
Spongy or soft floor – If your home was built with a wooden floor truss system, the sub floor is usually made of plywood, which forms the actual floor of your home. If this material is subject to moisture or hidden leaks, the plywood will rot and the floor will start to feel soft or spongy in places.
Do you tank under a shower tray?
If it is a wet room with a tiled floor and no shower tray then yes it needs tanking. In a nutshell, the tanking process is where tape is applied to the corners and joins and a waterproof coating is painted on. It is not always necessary to tank the floor if a shower tray and enclosure are being installed.
What do you put under shower base?
Mortar is recommended to use under all shower pans. Mortar reduces the risk of your pan slipping or cracking from an uneven surface.
Can you lay shower tray on floorboards?
When learning how to lay a shower tray on a wooden floor, you will need to mark the area where the tray will stand. Next, replace the floorboards within that area with a minimum of 18mm marine ply. You will need to ensure there is access to the waste pipes in the floor beside the tray.
Do shower trays have a weight limit?
Shower legs allow you to adjust the level of your tray. Each leg has a load-bearing capacity of up to 250 kg. Generally, shower tray legs range from 90 to 125 mm in height. In order to maintain balance – particularly on uneven floors – the number of legs should be tailored to the size of the tray.
Should a shower tray creak?
A squeaking shower base can indicate a leak or long-term water damage. Before attempting any remedies, check your drain and water lines for any signs of loose fittings or damaged pipes.
How much weight can an acrylic shower pan hold?
The base is designed to hold up to 300 LBS. But with the bed of mortar underneath it will hold even more. Yes, it works with all shower doors that size.
How much weight can a bathroom floor hold?
Based on some research, the typical home is constructed (US) to support 40 lbs/ft. Using this value brings the total weight limit of the entire bathroom to around 2,200 lbs.
How long should a shower base last?
A shower base should last between 15 and 20 years, depending on how well it is made. Typically, shower bases are a mortar concrete mix, so you shouldn’t have to worry about replacing them more than every decade or so.
How do you level a fiberglass shower pan?
Place the level across the top edges of the pan and check for level. Place wood shims up underneath the shower pan in the corresponding areas for shimmed installations. The shims are held in place by the weight of the pan. The pan is also screwed onto the wall studs through the flanges of the pan.
What is the proper slope for a shower floor?
In a stall shower, the plumbing code requires the floor to be sloped one quarter (1/4) of an inch per foot in order to carry the water effectively to the drain. This slope, according to the TCNA Handbook is called “sloped fill” or commonly known as the pre-slope.
Do I need mortar under fiberglass shower pan?
Quote from the video:
Quote from Youtube video: But yes so use your mortar underneath your fiberglass or acrylic shower. I love it it's a great way to support the bottom of that pan and make sure it never flexes.
Do you need to waterproof under a shower base?
Installation & Waterproofing
DON’T ignore the importance of waterproofing when installing an acrylic shower base. The walls and the area around the top of the acrylic base along the wall are very important for proper waterproofing and it is essential that it be done correctly.
How do you waterproof under a shower tray?
Quote from the video:
Quote from Youtube video: Seal. Before the installation commences lay a protective cover over the shower tray base below the working area mark the walls at points where the seelix profiles are intended to end.
How often should I reseal my shower tray?
It should be sufficient to reseal your shower every one to two years, depending on how frequently the shower system is used. Opt for a shower sealant labelled ‘Tub & Tile’ or ‘Kitchen & Bath’ when sealing tile and grout.
