How do I separate multiple lights on one switch?

3 Answers

  1. Get a 2-gang box to replace your existing 1-gang box.
  2. Get a new switch.
  3. Remove your existing box and install the 2-gang box in its place.
  4. Run your supply hot wire to both switches.
  5. Connect the light/fan hot wire to one switch and the exterior light to the other.
  6. Join all neutrals and ground wires.





Can I run 2 lights from one switch?

The answer is yes; one switch can turn on multiple lights. You can use two ways to make your switch control multiple lights. The most common way is to daisy-chain the light fixtures through connecting them with each other and hooking the first fixture to the switch.

Can you split a light circuit?

If you can make a run of romex NM from the single light circuit to one of the lamps of the 2 light circuit, you’ll be ok. Disconnect and cap off the feed to that other circuit as well as the wires to the unused switch. Then you can add the light to the desired circuit.

How many lights can you have on one switch?

You should have no problem supplying 8 light fixtures from a single 120 volt 15 ampere circuit, unless the fixtures have four or five bulbs each. @MatthewPerry a switch can control as many lights as are on the circuit, as long as the current drawn by the bulbs is less than the rated current of the switch.

How do you split a hot wire?





Quote from the video:
Quote from Youtube video: It back and forth. Until it gives up. So now that is officially divided there now the same thing on the hot side so that's a neutral prong. Obviously. I'm just gonna bend this back and forth.

How do you convert a one way switch to a two way?

Quote from the video:
Quote from Youtube video: And you need to check the back to ensure that they had three terminals on each if your one-way switch only has two terminals then you need to replace this.

How many lights can you string together?

In this case, most traditional incandescent Christmas mini lights only allow you to connect 4 or 5 sets end to end but with many LED mini light strings you can connect 40 to 50+ together depending on the light count. Consider your circuits: Most household circuits are 15 or 20 amps.

How many LED lights can you put on one circuit?

Assuming a 60 watt light, you can put up to 24 lights on a 15 amp breaker. If you are using low-wattage LED bulbs, an LED bulb using 10 watts, you can install up to 150 bulbs on a single circuit.

How many LED lights can you daisy-chain?



For example, if you choose a 120-volt power supply for daisy-chaining 10-watt LED tube lights, you will be able to connect 12 LEDs. However, to sail on the safer side, make sure that you do not connect more than seven tube lights to a power supply.

How do you daisy-chain lights together?

Quote from the video:
Quote from Youtube video: Light instead of having two main wires one main wire going to this light and another main wire going to this light and let's say you have a third light right here and then maybe a fourth. Light.

Can I daisy-chain recessed lights?

Remember that you must run one ultra-thin extension cable (or run of low voltage wire) for each light. You can not daisy chain multiple lights together.

Can you run lights and outlets on the same circuit?



Yes, you can. The average home uses an indoor distribution board that houses the breakers of the majority of circuits in the home. A circuit controlled by a 15A circuit breaker (which a lot of contractors use for general lighting) can also accommodate outlets.

How many lights and outlets should be on a circuit?

Technically, you can have as many outlets on a 15 amp circuit breaker as you want. However, a good rule of thumb is 1 outlet per 1.5 amps, up to 80% of the capacity of the circuit breaker. Therefore, we would suggest a maximum of 8 outlets for a 15 amp circuit.

Do bathroom lights need to be on their own circuit?

The bathroom electrical code now stipulates that the bathroom must have dedicated circuits that aren’t shared with outlets or lights in any other room. You must provide at least two of these circuits. One is a 20-amp circuit that powers the outlets, and the other is a 15-amp circuit for the lights.

Can living room lights and outlets be on the same circuit?

Yes, if you want, you can use separate circuits for your outlets and lights. In this process usually, a 15 amp circuit is used for lighting. For the outlets, you can use a 20 amp one. You can use 12 gauge wires for your lights on both the 20 and 15 amp circuits.

How many lights and outlets can be on a 15 amp circuit?



A 15-amp circuit is compatible with 8 outlets and lights.

How do you divide circuits in a house?

Splitting a double-tap circuit breaker is straightforward—you only need these two steps.

  1. Step 1: Disconnect One Line in your Double-tap Breaker.
  2. Step 2: Install Additional Circuit Breaker and Connect the Extra Line.
  3. Step 1: Find the Linked Wire in Your Junction Box.
  4. Step 2: Install a New Line.
  5. Step 3: Connect the Line.

How many LEDS can be on a 20 amp circuit?

Amount of Lights You Can Put on a 20-Amp Circuit Breaker



A standard 50-watt light consumes less than a half amperage on a 120-Volt circuit. With that fact, a 50-watt light on a 20-amp breaker can have a total of 38 lights on a circuit.

How many amps does a 4ft LED light draw?

The manufacturer says that the shop lights draw about 0.3amps. 6 times in a day. Round up to 2 is 3 Amps, which is only 1.8 Amps.

How many lights and outlets can you put on a 20 amp circuit?



One outlet has a power draw of up to 180 watts. Hence, a 20-amp 120-volt circuit can accommodate a maximum of 10 such outlets, with a sufficiently large margin for safety.